- 您現在的位置：買賣IC網 > PDF目錄384698 > MAX724 (Maxim Integrated Products, Inc.) 5A/2A Step-Down, PWM, Switch-Mode DC-DC Regulators PDF資料下載
參數資料
| 型號： | MAX724 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 5A/2A Step-Down, PWM, Switch-Mode DC-DC Regulators |
| 中文描述： | 5A/2A、降壓型、PWM、開關模式DC-DC穩壓器 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 92K |
| 代理商： | MAX724 |
M
5A/2A S tep-Down, PWM,
S witc h-Mode DC-DC Regulators
_______________________________________________________________________________________
5
______________________________________________________________Pin Desc ription
_________________Detailed Desc ription
The MAX724/MAX726 are complete, single-chip, pulse-
width modulation (PWM), step-down DC-DC converters
(Figure 1). All oscillator (100kHz), control, and current-
limit circuitry, including a 5A power switch (2A for
MAX726), are included on-chip. The oscillator turns on
the switch (V
) at the beginning of each clock cycle.
The switch turns off at a point later in the clock cycle,
which is a function of the signal provided by the error
amplifier. The maximum switch duty cycle is approxi-
mately 93% at the MAX724/MAX726's 100kHz switch-
ing frequency.
Both the input (FB) and output (V
) of the error
amplifier are brought out to simplify compensation.
Most applications require only a single series RC
network connected from V
to ground. The error
amplifier is a transconductance amplifier with a g
M
of
approximately 5000
μ
mho. When slewing, V
can
source about 140
μ
A, and sink about 1.1mA. This
asymmetry helps minimize start-up overshoot by
allowing the amplifier output to slew more quickly in
the negative direction.
Current limiting is provided by the current-limit com-
parator. If the current-limit threshold is exceeded, the
switch cycle terminates within about 600ns. The cur-
rent-limit threshold is internally set to approximately
6.5A (2.6A for MAX726). V
is a power NPN, internally
driven by the PWM controller circuitry. V
can swing
35V below ground and is rated for 5A (2A for MAX726).
Basic S tep-Down Applic ation
Figure 2 shows the MAX724/MAX726 in a basic step-
down DC-DC converter. Typical MAX724 waveforms
are shown in Figure 3 for V
= 20V, V
= 5V, L =
50
μ
H, and I
= 3A and 0.16A. Two sets of wave-
forms are shown. One set shows high load current (3A)
where inductor current never falls to zero during the
switch "off-cycle" (continuous-conduction mode, CCM).
The second set of waveforms, at low output current
(0.16A), shows inductor current at zero during the latter
half of the switch off-cycle (discontinuous-conduction
mode, DCM). The transition from CCM to DCM occurs
at an output current (I
DCM
) that can be derived with the
following equation:
I
DCM
=(V
OUT
+ V
D
) [(V
IN
- V
SW
) - (V
OUT
+ V
D
)]
2 (V
IN
- V
SW
) f
OSC
L
where V
is the diode forward voltage drop, V
is the
voltage drop across the switch, and f
= 100kHz. In
most applications, the distinction between CCM and
DCM is academic since actual performance differences
are minimal. All CCM designs can be expected to exhibit
DCM behavior at some level of reduced load current.
PIN
V
supplies power to the MAX724/MAX726's internal circuitry and also connects to the collector. V
IN
must be
bypassed with a low-ESR capacitor, typically 200μF or 220μF.
Internal Power Switch Output. The
S
witch output can swing 35V below ground and is rated for 5A (MAX724), 2A
(MAX726).
Ground requires a short low-noise connection to ensure good load regulation. The internal reference is referred
to GND, so errors at this pin are multiplied by the error amplifier. See the Applications Informationsection for
grounding details.
Error-Amplifier Output. A series RC network connected to this pin compensates the MAX724/MAX726. Output
swing is limited to about 5.8V in the positive direction and -0.7V in the negative direction. V
C
can also synchro-
nize the MAX724/MAX726 to an external clock. (See the Applications Informationsection).
Feedback Input is the error amplifier's inverting input, and controls output voltage by adjusting switch duty cycle.
Input bias current is typically 0.5μA when the error amplifier is balanced (I
= 0V). FB also aids current limiting
by reducing the oscillator frequency when the output voltage is low. (See the Applications Informationsection.)
V
IN
5
V
SW
4
GND
3
V
C
2
FB
1
FUNCTION
NAME
相關PDF資料 |
PDF描述 |
|---|---|
| MAX724ECK | Octal Buffers And Line Drivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX724CCK | 5A/2A Step-Down, PWM, Switch-Mode DC-DC Regulators |
| MAX7319 | 4-Bit D-type Registers with 3-State Outputs 16-CFP -55 to 125 |
| MAX732 | Hex D-type Flip-Flops With Clear 16-CFP -55 to 125 |
| MAX733 | +12V/+15V Step-Up Current-Mode Pwm Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX72408# | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX72408+ | 功能描述:接口 - 專用 BMC/EM RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX72408W+ | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX72420+ | 制造商:Maxim Integrated Products 功能描述:BASEBOARD AND STORAGE MANAGEMENT CONTROLLER - Rail/Tube |
| MAX72420+W | 制造商:Maxim Integrated Products 功能描述:BASEBOARD AND STORAGE MANAGEMENT CONTROLLER - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。