- 您現在的位置：買賣IC網 > PDF目錄383493 > MAX712MJE (MAXIM INTEGRATED PRODUCTS INC) Octal Buffers And Line Drivers With 3-State Outputs 20-LCCC -55 to 125 PDF資料下載
參數資料
| 型號： | MAX712MJE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Octal Buffers And Line Drivers With 3-State Outputs 20-LCCC -55 to 125 |
| 中文描述： | 0.1 A BATTERY CHARGE CONTROLLER, CDIP16 |
| 封裝： | CERDIP-16 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 168K |
| 代理商： | MAX712MJE |
M
NiCd/NiMH Battery
Fast-Charge Controllers
14
______________________________________________________________________________________
The voltage-slope, fast-charge termination circuitry
might become disabled if attempting to charge a
different number of cells than the number programmed.
The switching frequency (nominally 30kHz) can be
decreased by increasing the value of the capacitor
connected between CC and BATT-. Make sure that
the two capacitors connected to the CC node are
placed as close as possible to the CC pin on the
MAX712/MAX713 and that their leads are of minimum
length. The CC node is a high-impedance point, so do
not route logic lines near the CC pin. The circuit of
Figure 19 cannot service a load while charging.
Order the MAX713SWEVKIT-SO for quick evaluation of
the MAX712/MAX713 in switch-mode operation. For
more information on switch-mode operation and
ordering information for external components, order the
MAX713EVKIT data sheet.
Battery-Charging Examples
Figures 13 and 14 show the results of charging 3 AA,
1000mAh, NiMH batteries from Gold Peak (part no.
GP1000AAH, GP Batteries (619) 438-2202) at a 1A rate
using the MAX712 and MAX713, respectively. The
Typical Operating Circuit is used with Figure 9a’s
thermistor configuration .
DC IN = Sony AC-190 +9VDC at 800mA AC-DC adapter
PGM0 = V+, PGM1 = REF, PGM2 = REF, PGM3 = REF
R1 = 200
, R2 = 150
, R
SENSE
= 0.25
C1 = 1
μ
F, C2 = 0.01
μ
F, C3 = 10
μ
F, V
LIMIT
= REF
R3 = 10k
, R4 = 15k
T1, T2 = part #13A1002 (Alpha Thermistor: (800) 235-5445)
R5 omitted, T3 omitted, TLO = BATT-
11
6
5
0
200
LOAD CURRENT (mA)
600
1000
7
10
M
O
400
800
9
8
LOW PEAK
HIGH PEAK
120Hz
RIPPLE
Figure 11. Sony CD Player AC Adapter AC-96N Load
Characteristic, 9VDC 600mA
4.3
4.2
0
30
90
4.5
5.0
4.9
4.7
4.4
M
B
B
°
C
60
TIME (MINUTES)
4.8
4.6
tCUTOFF
26
24
30
40
38
34
28
36
32
V
T
Figure 13. 3 NiMH Cells Charged with MAX712
10
8
0
200
LOAD CURRENT (mA)
600
12
18
M
O
400
800
16
14
HIGH PEAK
LOW PEAK
120Hz
RIPPLE
Figure 12. Panasonic Modem AC Adapter KX-A11 Load
Characteristic, 12VDC 500mA
4.3
4.2
0
30
90
4.5
5.0
4.9
4.7
4.4
M
B
B
°
C
60
TIME (MINUTES)
4.8
4.6
26
24
30
40
38
34
28
36
32
tCUTOFF
V
T
Figure 14. NiMH Cells Charged with MAX713
相關PDF資料 |
PDF描述 |
|---|---|
| MAX713CPE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713CSE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713EPE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713ESE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713MJE | NiCd/NiMH Battery Fast-Charge Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX713 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Switch-Mode Battery Charger Delivers 5A |
| MAX713C/D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713CPE | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX713CPE+ | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX713CSE | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。