- 您現在的位置：買賣IC網 > PDF目錄385548 > MAX710ESE (MAXIM INTEGRATED PRODUCTS INC) 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters PDF資料下載
參數資料
| 型號： | MAX710ESE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters |
| 中文描述： | 0.7 A SWITCHING REGULATOR, PDSO16 |
| 封裝： | 0.150 INCH, MS-012C, SOIC-16 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 140K |
| 代理商： | MAX710ESE |
_______________Detailed Desc ription
The MAX710/MAX711 integrate a step-up DC-DC con-
verter with a linear regulator to provide step-up/down
voltage conversion. The step-up switch-mode regulator
contains an N-channel power MOSFET switch. It also
shares a precision voltage reference with a linear regu-
lator that contains a P-channel MOSFET pass element
(Figure 1).
S tep-Up Operation
A pulse-frequency-modulation (PFM) control scheme
with a constant 1μs off-time and variable on-time con-
trols the N-channel MOSFET switch. The N-channel
switch turns off when the part reaches the peak current
limit or the 4μs maximum on-time. The ripple frequency
is a function of load current and input voltage.
S tep-Down Operation
The low-dropout linear regulator consists of a refer-
ence, an error amplifier, and a P-channel MOSFET. The
reference is connected to the error amplifier’s inverting
input. The error amplifier compares this reference with
the selected feedback voltage and amplifies the differ-
ence. The difference is conditioned and applied to the
P-channel pass transistor’s gate.
Operating Configurations
The MAX710/MAX711 have several operating configu-
rations to minimize noise and optimize efficiency for dif-
ferent input voltage ranges. These configurations are
accomplished via the N/
E
input, which controls opera-
tion of the on-chip linear regulator.
With N/
E
low, the linear regulator behaves as a 0.7
(at
5V output) PFET switch when the IC is boosting, and as
a conventional linear regulator when V
IN
> V
OUT
. This
provides optimum boost efficiency, but the PFET does
little to reject boost-converter output ripple. With N/
E
high, boost ripple rejection is optimized by maintaining
headroom (V
FV
, typically 0.5V at 5V output) across the
linear regulator. Boost mode efficiency is then about
10% lower than with N/
E
high.
M
3.3V /5V or Adjustable,
S tep-Up/Down DC-DC Converters
6
_______________________________________________________________________________________
______________________________________________________________Pin Desc ription
Drain Connection for internal N-channel power MOSFET
LX
1
Power Ground
PGND
2
Shutdown Input. When low, the entire circuit is off and OUT is actively pulled to GND.
SHDN
4
Inductor Current-Limit-Select Input. Connect to GND for 1.5A limit and to PS for 0.8A limit.
ILIM
3
Standby Input. Connect to GND to disable boost circuit. Connect to PS for normal operation.
STBY
5
Selects low-noise or high-efficiency mode. Connect to GND for high efficiency and to PS for
lowest noise. See Operating Configurations section.
N/
E
7
Selects the output voltage. Connect to GND for 5V output and to OUT for 3.3V output.
3/
5
6
2
4
3
5
7
—
1
Low-Battery Comparator Output
LBO
8
8
Negative Input to Low-Battery Comparator
LBI-
10
Source of internal PFET regulator. The IC is powered from PS.
PS
12
Positive Input to Low-Battery Comparator
LBI+
11
1.28V Reference Voltage Output. Bypass with a 0.1μF capacitor to GND.
REF
13
Power Ground
PGND
15
Analog Ground. Must be low impedance. Solder directly to ground plane.
GND
14
10
12
11
13
15
14
9
Drain Connection for internal N-channel power MOSFET
LX
16
16
Linear-Regulator Output. Bypass with a 4.7μF capacitor to GND.
OUT
9
MAX711
MAX710
FUNCTION
NAME
PIN
Feedback Input
FB
—
6
相關PDF資料 |
PDF描述 |
|---|---|
| MAX711ESE | 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters |
| MAX7129CQL | Analog to Digital Converter |
| MAX7129 | 4-1/2 Digit Single-Chip A/D Converter with LCD Driver |
| MAX7129CJL | 4-1/2 Digit Single-Chip A/D Converter with LCD Driver |
| MAX7129CPL | 4-1/2 Digit Single-Chip A/D Converter with LCD Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX710ESE+ | 功能描述:直流/直流開關轉換器 3.3/5V or Adjustable Step-Up Step-Down RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX710ESE+ | 制造商:Maxim Integrated Products 功能描述:CONVERTOR DC/DC ((NW)) |
| MAX710ESE+T | 功能描述:直流/直流開關轉換器 3.3/5V or Adjustable Step-Up Step-Down RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX710ESE-T | 功能描述:直流/直流開關轉換器 3.3/5V or Adjustable Step-Up Step-Down RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX710EVKIT | 功能描述:直流/直流開關轉換器 Evaluation Kit for the MAX710 MAX711 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。