- 您現在的位置：買賣IC網 > PDF目錄385547 > MAX707 (Maxim Integrated Products, Inc.) Low-Cost,μP Supervisory Circuits(帶有掉電報警復位器,復位門限4.65V) PDF資料下載
參數資料
| 型號： | MAX707 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Cost,μP Supervisory Circuits(帶有掉電報警復位器,復位門限4.65V) |
| 中文描述： | 低成本、微處理器監控電路 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 129K |
| 代理商： | MAX707 |
M
_______________Detailed Desc ription
Reset Output
A microprocessor’s (μP’s) reset input starts the μP in a
known state. Whenever the μP is in an unknown state, it
should be held in reset. The MAX705-MAX708/MAX813L
assert reset during power-up and prevent code execu-
tion errors during power-down or brownout conditions.
On power-up, once V
CC
reaches 1V, RESET is a guaran-
teed logic low of 0.4V or less. As V
CC
rises, RESET stays
low. When V
CC
rises above the reset threshold, an inter-
nal timer releases RESET after about 200ms. RESET puls-
es low whenever V
CC
dips below the reset threshold, i.e.
brownout condition. If brownout occurs in the middle of
a previously initiated reset pulse, the pulse continues for
at least another 140ms. On power-down, once V
CC
falls
below the reset threshold, RESET stays low and is guar-
anteed to be 0.4V or less until V
CC
drops below 1V.
The MAX707/MAX708/MAX813L active-high RESET output
is simply the complement of the RESET output, and is
guaranteed to be valid with V
CC
down to 1.1V. Some μPs,
such as Intel’s 80C51, require an active-high reset pulse.
Watc hdog T imer
The MAX705/MAX706/MAX813L watchdog circuit moni-
tors the μP’s activity. If the μP does not toggle the watch-
dog input (WDI) within 1.6sec and WDI is not three-stat-
ed, WDO goes low. As long as RESET is asserted or the
WDI input is three-stated, the watchdog timer will stay
cleared and will not count. As soon as reset is released
and WDI is driven high or low, the timer will start counting.
Pulses as short as 50ns can be detected.
Typically, WDO will be connected to the non-maskable
interrupt input (NMI) of a μP. When V
CC
drops below
the reset threshold, WDO will go low whether or not the
watchdog timer has timed out yet. Normally this would
trigger an NMI interrupt, but RESET goes low simultane-
ously, and thus overrides the NMI interrupt.
If WDI is left unconnected, WDO can be used as a low-
line output. Since floating WDI disables the internal
timer, WDO goes low only when V
CC
falls below the
reset threshold, thus functioning as a low-line output.
The MAX705/MAX706 have a watchdog timer and a
RESET output. The MAX707/MAX708 have both active-
high and active-low reset outputs. The MAX813L has
both an active-high reset output and a watchdog timer.
Manual Reset
The manual-reset input (MR) allows reset to be trig-
gered by a pushbutton switch. The switch is effectively
debounced by the 140ms minimum reset pulse width.
MR is TTL/CMOS logic compatible, so it can be driven
by an external logic line. MR can be used to force a
watchdog timeout to generate a reset pulse in the
MAX705/MAX706/MAX813L. Simply connect WDO to
MR.
Low-Cost, μP S upervisory Circ uits
6
_______________________________________________________________________________________
WATCHDOG
TRANSITION
DETECTOR
WATCHDOG
TIMER
TIMEBASE FOR
RESET AND
WATCHDOG
RESET
GENERATOR
V
CC
250
μ
A
8
WDO
7
RESET
(RESET)
5
PFO
GND
3
1.25V
4.65V*
* 4.40V FOR MAX7O6.
( ) ARE FOR MAX813L ONLY.
6
WDI
1
MR
2
V
CC
4
PFI
MAX705
MAX706
MAX813L
Figure 1. MAX705/MAX706/MAX813L Block Diagram
RESET
GENERATOR
V
CC
250
μ
A
8
RESET
7
RESET
5
PFO
GND
3
1.25V
4.65V*
* 4.40V FOR MAX7O6.
1
MR
2
V
CC
4
PFI
MAX707
MAX708
Figure 2. MAX707/MAX708 Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX707 | μP Supervisory Circuits(μP監控電路) |
| MAX708 | μP Supervisory Circuits(μP監控電路) |
| MAX711 | 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters |
| MAX710 | 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters |
| MAX710ESE | 3.3V/5V or Adjustable, Step-Up/Down DC-DC Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX707/D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:?P Supervisory Circuits |
| MAX707C/D | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX707CPA | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX707CPA+ | 功能描述:監控電路 Single uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX707CSA | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。