- 您現在的位置：買賣IC網 > PDF目錄385547 > MAX7030HATJ (MAXIM INTEGRATED PRODUCTS INC) Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL PDF資料下載
參數資料
| 型號： | MAX7030HATJ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通信及網絡 |
| 英文描述： | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, 0.80 MM HEIGHT, MO-220WHHD-2, TQFN-32 |
| 文件頁數： | 15/20頁 |
| 文件大小： | 735K |
| 代理商： | MAX7030HATJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁
M
Low-Cost, 315MHz, 345MHz, and 433.92MHz
ASK Transceiver with Fractional-N PLL
______________________________________________________________________________________
15
Peak Detectors
The maximum peak detector (PDMAX) and minimum
peak detector (PDMIN), with resistors and capacitors
shown in
Figure
3, create DC output voltages equal to
the high- and low-peak values of the filtered demodulat-
ed signal. The resistors provide a path for the capaci-
tors to discharge, allowing the peak detectors to
dynamically follow peak changes of the data filter out-
put voltages.
The maximum and minimum peak detectors can be
used together to form a data slicer threshold voltage at
a value midway between the maximum and minimum
voltage levels of the data stream (see the
Data Slicer
section and
Figure
3). Set the RC time constant of the
peak detector combining network to at least 5 times the
data period.
If there is an event that causes a significant change in
the magnitude of the baseband signal, such as an AGC
gain-switch or a power-up transient, the peak detectors
may “catch” a false level. If a false peak is detected,
the slicing level is incorrect. The MAX7030 peak detec-
tors correct these problems by temporarily tracking the
incoming baseband filter voltage when an AGC state
switch occurs, or forcing the peak detectors to track the
baseband filter output voltage until all internal circuits
are stable following an enable pin low-to-high transition
and also T/
R
pin high-to-low transition. The peak detec-
tors exhibit a fast attack/slow decay response. This fea-
ture allows for an extremely fast startup or AGC
recovery.
Transmitter
Power Amplifier (PA)
The PA of the MAX7030 is a high-efficiency, open-
drain, class-C amplifier. The PA with proper output-
matching network can drive a wide range of antenna
impedances, which includes a small-loop PC board
trace and a 50
antenna. The output-matching network
for a 50
antenna is shown in the
Typical Application
Circuit
. The output-matching network suppresses the
carrier harmonics and transforms the antenna imped-
ance to an optimal impedance at PAOUT (pin 5). The
optimal impedance at PAOUT is 250
.
When the output-matching network is properly tuned,
the PA transmits power with a high overall efficiency of
up to 32%. The efficiency of the PA itself is more than
46%. The output power is set by an external resistor at
PAOUT, and is also dependent on the external antenna
and antenna-matching network at the PA output.
Envelope Shaping
The MAX7030 features an internal envelope-shaping
resistor, which connects between the open-drain output
of the PA and the power supply (see the
Typical
Application Circuit
). The envelope-shaping resistor
slows the turn-on/turn-off of the PA in ASK mode, and
results in a smaller spectral width of the modulated PA
output signal.
Fractional-N Phase-Locked Loop (PLL)
The MAX7030 utilizes a fully integrated, fractional-N,
PLL for its transmit frequency synthesizer. All PLL com-
ponents, including the loop filter, are integrated inter-
nally. The loop bandwidth is approximately 200kHz.
Power-Supply Connections
The MAX7030 can be powered from a 2.1V to 3.6V sup-
ply or a 4.5V to 5.5V supply. If a 4.5V to 5.5V supply is
used, then the on-chip linear regulator reduces the 5V
supply to the 3V needed to operate the chip.
To operate the MAX7030 from a 3V supply, connect
PAV
DD
, AV
DD
, DV
DD
, and HV
IN
to the 3V supply. When
using a 5V supply, connect the supply to HV
IN
only and
MAX7030
C
PDMAX
PDMIN
R
C
R
DATA
SLICER
DATA
DET
DET
Figure 3. Generating Data-Slicer Threshold Using the Peak
Detectors
MAX7030
C
DS-
DS+
R
DATA
SLICER
DATA
Figure 2. Generating Data-Slicer Threshold Using a Lowpass
Filter
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7030LATJ | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| MAX7030MATJ | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| MAX703 | Low-Cost レP Supervisory Circuits with Battery Backup |
| MAX703-MAX704 | Low-Cost レP Supervisory Circuits with Battery Backup |
| MAX703CPA | Quadruple 2-Line To 1-Line Data Selectors/Multiplexers 16-CFP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7030HATJ+ | 功能描述:射頻收發器 315/345/433.92MHz ASK Transceiver RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| MAX7030HATJ+T | 功能描述:射頻收發器 315/345/433.92MHz ASK Transceiver RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| MAX7030HATJ-T | 制造商:Maxim Integrated Products 功能描述:LOW-COST,CRYSTAL-BASED,315MHZ,345MHZ,&433.92M - Tape and Reel |
| MAX7030LATJ | 制造商:Maxim Integrated Products 功能描述:LOW-COST,CRYSTAL-BASED,315MHZ,345MHZ,&433.92M - Rail/Tube |
| MAX7030LATJ+ | 功能描述:射頻收發器 315/345/433.92MHz ASK Transceiver RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。