- 您現在的位置：買賣IC網 > PDF目錄385547 > MAX7030-ATJ (Maxim Integrated Products, Inc.) Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL PDF資料下載
參數資料
| 型號： | MAX7030-ATJ |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| 中文描述： | 低成本，315MHz的，345MHz用于和433.92MHz的調幅收發器的分?jǐn)?shù)N PLL |
| 文件頁數： | 13/20頁 |
| 文件大小： | 735K |
| 代理商： | MAX7030-ATJ |
M
Low-Cost, 315MHz, 345MHz, and 433.92MHz
ASK Transceiver with Fractional-N PLL
______________________________________________________________________________________
13
AGC Dwell-Time Settings
The AGC dwell timer holds the AGC in low-gain state
for a set amount of time after the power level drops
below the AGC switching threshold. After that set
amount of time, if the power level is still below the AGC
threshold, the LNA goes into high-gain state. This is
important for ASK since the modulated data may have
a high level above the threshold and low level below
the threshold, which without the dwell timer would
cause the AGC to switch on every bit.
The MAX7030 uses the three AGC control pins (AGC0,
AGC1, AGC2) to set seven user-controlled, dwell-timer
settings. The AGC dwell time is dependent on the crys-
tal frequency and the bit settings of the AGC control
pins. To calculate the dwell time, use the following
equation:
where K is an odd integer in decimal from 11 to 23, deter-
mined by the control pin settings shown in
Table
1.
To calculate the value of K, use the following equation
and use the next integer higher than the calculated
result:
K
≥
3.3 x log
10
(Dwell Time x f
XTAL
)
For Manchester Code (50% duty cycle), set the dwell
time to at least twice the bit period. For nonreturn-to-
zero (NRZ) data, set the dwell to greater than the peri-
od of the longest string of zeros or ones. For example,
using Manchester Code at 315MHz (f
XTAL
=
12.679MHz) with a data rate of 2kbps (bit period =
250μs), the dwell time needs to be greater than 500μs:
K
≥
3.3 x log
10
(500μs x 12.679)
≈
12.546
Choose the AGC pin settings for K to be the next odd-
integer value higher than 12.546, which is 13. This says
that AGC1 is set high and AGC0 and AGC2 are set low.
Mixer
A unique feature of the MAX7030 is the integrated
image rejection of the mixer. This eliminates the need
for a costly front-end SAW filter for many applications.
The advantage of not using a SAW filter is increased
sensitivity, simplified antenna matching, less board
space, and lower cost.
The mixer cell is a pair of double-balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz intermediate frequency (IF) with low-side
injection (i.e., f
LO
= f
RF
- f
IF
). The image-rejection circuit
then combines these signals to achieve a typical 46dB
of image rejection over the full temperature range. Low-
side injection is required as high-side injection is not
possible due to the on-chip image rejection. The IF out-
put is driven by a source follower, biased to create a
driving impedance of 330
to interface with an off-chip
330
ceramic IF filter. The voltage-conversion gain dri-
ving a 330
load is approximately 20dB. Note that the
MIXIN+ and MIXIN- inputs are functionally identical.
Integer-N Phase-Locked Loop (PLL)
The MAX7030 utilizes a fixed-integer-N PLL to generate
the receive LO. All PLL components, including the loop
filter, voltage-controlled oscillator, charge pump, asyn-
chronous 24x divider, and phase-frequency detector
are integrated internally. The loop bandwidth is approx-
imately 500kHz. The relationship between RF, IF, and
reference frequencies is given by:
f
REF
= (f
RF
- f
IF
) / 24
Dwell Time
f
K
XTAL
=
2
AGC2
0
0
0
0
1
1
1
1
AGC1
0
0
1
1
0
0
1
1
AGC0
0
1
0
1
0
1
0
1
DESCRIPTION
AGC disabled, high gain selected
K = 11
K = 13
K = 15
K = 17
K = 19
K = 21
K = 23
Table
1. AGC Dwell Time Settings for
MAX7030
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7030HATJ | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| MAX7030LATJ | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| MAX7030MATJ | Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL |
| MAX703 | Low-Cost レP Supervisory Circuits with Battery Backup |
| MAX703-MAX704 | Low-Cost レP Supervisory Circuits with Battery Backup |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7030EVKIT-315 | 功能描述:射頻接收器 Low-Cost 315MHz 345MHz and 433.92MHz ASK Transceiver with Fractional-N PLL RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MAX7030EVKIT-433 | 功能描述:射頻接收器 Low-Cost 315MHz 345MHz and 433.92MHz ASK Transceiver with Fractional-N PLL RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| MAX7030HATJ | 制造商:Maxim Integrated Products 功能描述:LOW-COST,CRYSTAL-BASED,315MHZ,345MHZ,&433.92M - Rail/Tube |
| MAX7030HATJ+ | 功能描述:射頻收發器 315/345/433.92MHz ASK Transceiver RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| MAX7030HATJ+T | 功能描述:射頻收發器 315/345/433.92MHz ASK Transceiver RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。