- 您現在的位置：買賣IC網 > PDF目錄384695 > MAX6978AUE (MAXIM INTEGRATED PRODUCTS INC) 8-Port, 5.5V Constant-Current LED Driver with LED Fault Detection and Watchdog PDF資料下載
參數資料
| 型號： | MAX6978AUE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | 8-Port, 5.5V Constant-Current LED Driver with LED Fault Detection and Watchdog |
| 中文描述： | LED DISPLAY DRIVER, PDSO16 |
| 封裝： | 4.40 MM, MO-153ABT, TSSOP-16 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 327K |
| 代理商： | MAX6978AUE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
M
OE
is independent of the operation of the serial inter-
face. Data can be shifted into the serial-interface shift
register and latched regardless of the state of
OE
.
DOUT is the serial-data output, which shifts data out
from the MAX6978’s 8-bit shift register on the rising edge
of CLK. Data at DIN is propagated through the shift reg-
ister and appears at DOUT eight clock cycles later.
Watchdog
The MAX6978 includes a watchdog circuit that monitors
the CLK, DIN, and LE inputs. If there is no transition on
any one of these inputs for nominally 1s, then the output
latches are cleared and outputs OUT0–OUT7 go high
impedance like the initial power-up condition. This turns
off all LEDs connected to the outputs. The shift-register
data does not change, just the output-latch data.
The watchdog is intended to be used as a fail-safe fea-
ture for applications, which prefer a blank display to an
incorrect display if the serial interface fails. When the
watchdog triggers, the outputs remain off until the dri-
ver output latches are updated with data turning them
on. Recovery is therefore automatic if the transmission
failure is temporary, because the MAX6978 does not
lock up in the watchdog timeout state. The MAX6978
operates correctly when the serial interface is next acti-
vated, and the watchdog circuit is reset and starts
monitoring the serial interface again. The watchdog
function requires no software change to the application
driving the MAX6978.
LED Fault Detection
The MAX6978 includes circuitry that detects open-cir-
cuit LEDs automatically. An open-circuit fault occurs
when an output is programmed to sink current but less
than about 50% of the programmed current flows.
Open circuits are checked just after the rising edge of
LE, when new LED data is loaded into the output latch-
es from the shift register(s). If one or more output port is
detected with an open-circuit fault, then the 2 bits, D6
and D5, in the serial-interface shift register are both set
high. If no open-circuit faults are detected, then D6 and
D5 are both cleared low. The data in other 6-bit posi-
tions in the serial-interface shift register is not altered.
Fault status is automatically shifted out on DOUT when
the next data transmission is shifted in. LE is normally
taken high after all 8 bits of new LED data have been
clocked into the shift register, and so at that time,
DOUT is outputting data bit D7. On the next two rising
edges of CLK, the 2 fault status bits, D6 and D5, are
clocked out in that order, followed by the remaining 5
unchanged data bits D4 to D0.
A typical fault-detecting application tests all the shifted
out data. Bits D0–D4 and D7 are checked against the
originally transmitted data to check data link integrity.
Bits D5 and D6 are checked first to see that they con-
8-Port, 5.5V Constant-Current LED Driver with
LED Fault Detection and Watchdog
8
_______________________________________________________________________________________
.
D7
D6
t
DS
t
DH
t
CL
t
CP
t
DO
t
OEW
t
OEL
t
f
t
r
t
OEH
t
LS
t
LW
t
LF
t
CH
D1
D0
D7
LE
CLK
DIN
DOUT
OE
OUT_
80%
20%
Figure 2. 4-Wire Serial-Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6978APE | 8-Port, 5.5V Constant-Current LED Driver with LED Fault Detection and Watchdog |
| MAX6978AEE | 8-Port, 5.5V Constant-Current LED Driver with LED Fault Detection and Watchdog |
| MAX6979 | AND-OR-invert Gates 14-CDIP -55 to 125 |
| MAX6980 | 4-Wide AND-OR-invert Gates 14-CFP -55 to 125 |
| MAX6981 | Octal Buffers And Line Drivers With 3-State Outputs 20-LCCC -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6978AUE+ | 功能描述:LED顯示驅動器 8-Port, 5.5V CC LED Driver w/Fault Det RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6978AUE+T | 功能描述:LED照明驅動器 8-Port, 5.5V CC LED Driver w/Fault Det RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX6978AUE-T | 功能描述:LED照明驅動器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX6979ANG | 功能描述:LED顯示驅動器 RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6979APG | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。