- 您現在的位置：買賣IC網 > PDF目錄380434 > MAX6967AEE (MAXIM INTEGRATED PRODUCTS INC) 10-Port Constant-Current LED Drivers and I/O Expanders with PWM Intensity Control PDF資料下載
參數資料
| 型號： | MAX6967AEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | 10-Port Constant-Current LED Drivers and I/O Expanders with PWM Intensity Control |
| 中文描述： | LED DISPLAY DRIVER, PDSO16 |
| 封裝： | 0.150 INCH, 0.025 MM PITCH, MO-137AB, QSOP-16 |
| 文件頁數： | 1/29頁 |
| 文件大?。?/td> | 398K |
| 代理商： | MAX6967AEE |
當前第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
General Description
The MAX6966/MAX6967 serial-interfaced peripherals
provide microprocessors with 10 I/O ports rated to 7V.
Each port can be individually configured as either:
A 20mA constant-current LED driver (static or pulse-
width modulated (PWM)).
A 10mA constant-current LED driver (static or PWM).
An open-drain logic output.
An overvoltage-protected Schmitt logic input.
Analog and switching LED intensity control is built in:
Individual 8-bit PWM control per output.
Individual 1-bit analog control (half/full) per output.
Global 3-bit analog control applies to all LED outputs.
PWM timing of the 10 port outputs may be optionally
staggered, consecutively phased in 45° increments.
This spreads the PWM load currents over time in eight
steps, helping to even out the power-supply current
and reduce the RMS current.
The MAX6966/MAX6967 can be configured to awake
from shutdown on receipt of a minimum 3ms pulse on
the
CS
input. This hardware-wakeup feature allows a
power-management controller or similar ASIC to enable
the MAX6966/MAX6967 with preconfigured LED intensi-
ty settings.
Shutdown can be programmed to wait up to 4s, fade
down the sink currents to zero for a period of 1/16s to
4s, and then shut down. A similar ramp-up from shut-
down can be programmed for 1/16s to 4s.
The MAX6966/MAX6967 support hot insertion. All port
pins remain high impedance in power-down (V+ = 0V)
with up to 8V asserted on them.
The DOUT/OSC pin can be configured as either the
serial interface data output or optional PWM clock
input. The MAX6966 powers up defaulting as DOUT
output. The MAX6967 defaults as OSC input.
For a similar part without the constant-current controls,
refer to the MAX7317 data sheet.
Applications
RGB LED Drivers
Portable Equipment
Cellular Phones
LCD Backlights
Keypad Backlights
LED Status Indication
Features
High-Speed 26MHz SPI-/QSPI-/MICROWIRE-
Compatible Serial Interface
2.25V to 3.6V Operation
I/O Ports Default to High-Z (LEDs Off) on Power-Up
I/O Port Inputs Are Overvoltage Protected to 7V
I/O Port Outputs Are 7V-Rated Open Drain
I/O Port Outputs Are 10mA or 20mA Constant-
Current Static/PWM LED Drivers, or Open-Drain
Logic Outputs
I/O Ports Support Hot Insertion
Individual 8-Bit PWM Intensity Control for Each LED
Any Output May Use or Not Use PWM Control
Exit Shutdown (Warm Start) with Simple
CS
Pulse
Auto Ramp-Down into Shutdown
Auto Ramp-Up Out from Shutdown
0.8μA (typ), 2μA (max) Shutdown Current
Tiny 3mm x 3mm, 0.8mm High Thin QFN Package
-40°C to +125°C Temperature Range
M
10-Port Constant-Current LED Drivers and I/O
Expanders with PWM Intensity Control
________________________________________________________________
Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
Ordering Information
19-3487; Rev 2; 4/05
PART
TEMP
RANGE
PIN-
PACKAGE
TOP
MARK
PKG
CODE
MAX6966
ATE
-40
°
C to
+125
°
C
16 Thin QFN
3mm x 3mm x
0.8mm
ACF
T1633-4
MAX6966AEE
-40
°
C to
+125
°
C
16 QSOP
—
—
MAX6967
ATE
-40
°
C to
+125
°
C
16 Thin QFN
3mm x 3mm x
0.8mm
ACG
T1633-4
MAX6967AEE
-40
°
C to
+125
°
C
16 QSOP
—
—
SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7044 | 300MHz to 450MHz High-Efficiency, Crystal-Based +13dBm ASK Transmitter |
| MAX7044AKA-T | 300MHz to 450MHz High-Efficiency, Crystal-Based +13dBm ASK Transmitter |
| MAX708TEPA | +3V Voltage Monitoring, Low-Cost, レP Supervisory Circuits |
| MAX706S | +3V Voltage Monitoring, Low-Cost, レP Supervisory Circuits |
| MAX706 | +3V Voltage Monitoring, Low-Cost, レP Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6967AEE+ | 功能描述:LED顯示驅動器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6967AEE+T | 功能描述:LED顯示驅動器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6967AEE-T | 功能描述:LED顯示驅動器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6967ATE | 功能描述:LED顯示驅動器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6967ATE+ | 功能描述:LED顯示驅動器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。