- 您現在的位置：買賣IC網 > PDF目錄385547 > MAX6957AGL (MAXIM INTEGRATED PRODUCTS INC) 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander PDF資料下載
參數資料
| 型號： | MAX6957AGL |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
| 中文描述： | LED DISPLAY DRIVER, QCC40 |
| 封裝： | QFN-40 |
| 文件頁數： | 7/23頁 |
| 文件大?。?/td> | 333K |
| 代理商： | MAX6957AGL |
Serial Interface
The MAX6957 communicates through an SPI-compati-
ble 4-wire serial interface. The interface has three
inputs, Clock (SCLK), Chip Select (
CS
), and Data In
(DIN), and one output, Data Out (DOUT).
CS
must be
low to clock data into or out of the device, and DIN
must be stable when sampled on the rising edge of
SCLK. DOUT provides a copy of the bit that was input
15.5 clocks earlier, or upon a query it outputs internal
register data, and is stable on the rising edge of SCLK.
Note that the SPI protocol expects DOUT to be high
impedance when the MAX6957 is not being accessed;
DOUT on the MAX6957 is never high impedance.
SCLK and DIN may be used to transmit data to other
peripherals, so the MAX6957 ignores all activity on
SCLK and DIN except between the fall and subsequent
rise of
CS
.
Control and Operation Using the
4-Wire Interface
Controlling the MAX6957 requires sending a 16-bit
word. The first byte, D15 through D8, is the command
address (Table 3), and the second byte, D7 through
D0, is the data byte (Table 4).
Connecting Multiple MAX6957s to the 4-Wire Bus
Multiple MAX6957s may be daisy-chained by connect-
ing the DOUT of one device to the DIN of the next, and
driving SCLK and
CS
lines in parallel (Figure 4). Data at
DIN propagates through the internal shift registers and
appears at DOUT 15.5 clock cycles later, clocked out
on the falling edge of SCLK. When sending commands
M
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
_______________________________________________________________________________________
7
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
R/W
8
CE
DATA
8
TEST REGISTER
INTENSITY REGISTERS
PORT REGISTERS
LED DRIVERS AND GPIO
INTENSITY
CONFIGURATION
TEST
P4 TO P31
LED DRIVERS
OR GPIO
SEGMENT OR
GPIO DATA
R/W
CONFIGURATION
REGISTERS
PORT CHANGE
DETECTOR
MASK REGISTER
COMMAND
REGISTER DECODE
8
8
DATA BYTE
COMMAND BYTE
CS
DIN
SCLK
DOUT
Figure 1. MAX6957 Functional Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6957ANI | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
| MAX6964 | 17- OUTPUT LED DRIVER/GPO |
| MAX6964AEG | 17- OUTPUT LED DRIVER/GPO |
| MAX6964ATG | 17- OUTPUT LED DRIVER/GPO |
| MAX696 | Microprocessor Supervisory Circuits(微處理器監控器/電池開關/可編程的復位) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6957AGL+ | 功能描述:LED顯示驅動器 2.5-5.5V 20/28Port LED Display Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6957ANI | 功能描述:LED顯示驅動器 2.5-5.5V 20/28Port LED Display Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6957ANI+ | 功能描述:LED顯示驅動器 2.5-5.5V 20/28Port LED Display Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6957APL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX6957ATL | 功能描述:LED顯示驅動器 RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。