- 您現在的位置：買賣IC網 > PDF目錄385547 > MAX6954APL (MAXIM INTEGRATED PRODUCTS INC) 4-Wire Interfaced, 2.7V to 5.5V LED Display Driver with I/O Expander and Key Scan PDF資料下載
參數資料
| 型號： | MAX6954APL |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | 4-Wire Interfaced, 2.7V to 5.5V LED Display Driver with I/O Expander and Key Scan |
| 中文描述： | LED DISPLAY DRIVER, PDIP40 |
| 封裝： | PLASTIC, DIP-40 |
| 文件頁數： | 6/38頁 |
| 文件大?。?/td> | 395K |
| 代理商： | MAX6954APL |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
M
Detailed Desc ription
The MAX6954 is a serially interfaced display driver that
can drive up to 16 digits 7-segment, 8 digits 14-seg-
ment, 8 digits 16-segment, 128 discrete LEDs, or a
combination of these display types. Table 1 shows the
drive capability of the MAX6954 for monocolor and
bicolor displays.
The MAX6954 includes 104-character ASCII font maps
for 14-segment and 16-segment displays, as well as
the hexadecimal font map for 7-segment displays. The
characters follow the standard ASCII font, with the
addition of the following common symbols: ￡,
€
,
￥
,
°
, μ,
±,
↑
, and
↓
. Seven bits represent the 104-character font
map; an 8th bit is used to select whether the decimal
point (DP) is lit. Seven-segment LED digits may be con-
trolled directly or use the hexadecimal font. Direct seg-
ment control allows the MAX6954 to be used to drive
bar graphs and discrete LED indicators.
Tables 2, 3, and 4 list the connection schemes for 16-,
14-, and 7-segment digits, respectively. The letters in
Tables 2, 3, and 4 correspond to the segment labels
shown in Figure 1. (For applications that require mixed
display types, see Tables 37
–
40.)
S erial Interfac e
The MAX6954 communicates through an SPI-compati-
ble 4-wire serial interface. The interface has three
4-Wire Interfac ed, 2.7V to 5.5V LED Display
Driver with I/O Expander and K ey S c an
6
_______________________________________________________________________________________
Pin Desc ription
PIN
SSOP
PDIP
NAME
FUNCTION
1, 2,
34, 35, 36
1, 2,
38, 39, 40
P0
–
P4
General-Purpose I/O Ports (GPIOs). GPIO can be configured as logic inputs or open-drain
outputs. Enabling key scanning configures some or all ports P0
–
P3 as key-switch matrix
inputs with internal pullup and port P4 as IRQ output.
3
3
CS
Chip-Select Input. Serial data is loaded into the shift register while
CS
is low. The most recent
16 bits of data latch on
CS
’
s rising edge.
4
4
DOUT
Serial-Data Output. The data into DIN is valid at DOUT 15.5 clock cycles later. Use this pin to
daisy-chain several devices or allow data readback. Output is push-pull.
5
5
CLK
Serial-Clock Input. On CLK
’
s rising edge, data shifts into the internal shift register. On CLK
’
s
falling edge, data is clocked out of DOUT. CLK is active only while
CS
is low.
6
6
DIN
Serial-Data Input. Data from DIN loads into the internal 16-bit shift register on CLK
’
s rising
edge.
7
–
15,
22
–
31
7
–
15,
26
–
35
O0
–
O18
Digit/Segment Drivers. When acting as digit drivers, outputs O0 to O7 sink current from the
display common cathodes. When acting as segment drivers, O0 to O18 source current to the
display anodes. O0 to O18 are high impedance when not being used as digit or segment
drivers.
16, 18
17, 18, 20
GND
Ground
17
19
ISET
Segment Current Setting. Connect ISET to GND through series resistor R
SET
to set the peak
current.
19, 21
21, 23, 24
V+
Positive Supply Voltage. Bypass V+ to GND with a 47μF bulk capacitor and a 0.1μF ceramic
capacitor.
20
22
OSC
Multiplex Clock Input. To use internal oscillator, connect capacitor C
SET
from OSC to GND.
To use external clock, drive OSC with a 1MHz to 8MHz CMOS clock.
32
36
BLINK
Blink Clock Output. Output is open drain.
33
37
OSC_OUT
Clock Output. OSC_OUT is a buffered clock output to allow easy blink synchronization of
multiple MAX6954s. Output is push-pull.
—
16, 25
N.C.
Not Internally Connected
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6954 | Dual 4-Bit Decade And Binary Counters 16-CFP -55 to 125 |
| MAX6954AAX | Dual 4-Bit Decade And Binary Counters 20-LCCC -55 to 125 |
| MAX6957 | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
| MAX6957AAI | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
| MAX6957AAX | 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28-Port LED Display Driver and I/O Expander |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6954APL+ | 功能描述:LED顯示驅動器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6954ATL | 功能描述:LED顯示驅動器 RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6954ATL+ | 功能描述:LED顯示驅動器 2.7-5.5V LED Display Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6954ATL+T | 功能描述:LED顯示驅動器 2.7-5.5V LED Display Driver RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MAX6954ATL-T | 功能描述:LED顯示驅動器 RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。