參數資料
型號: MAX6818EAP
廠商: Maxim Integrated Products
文件頁數: 4/8頁
文件大?。?/td> 0K
描述: IC DEBOUNCER SWITCH OCTAL 20SSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 66
系列: *
應用: *
接口: *
電源電壓: *
封裝/外殼: 20-SSOP(0.209",5.30mm 寬)
供應商設備封裝: 20-SSOP
包裝: 管件
安裝類型: 表面貼裝
_______________Detailed Description
Theory of Operation
The MAX6816/MAX6817/MAX6818 are designed to
eliminate the extraneous level changes that result from
interfacing with mechanical switches (switch bounce).
Virtually all mechanical switches bounce upon opening
or closing. These switch debouncers remove bounce
when a switch opens or closes by requiring that
sequentially clocked inputs remain in the same state for
a number of sampling periods. The output does not
change until the input is stable for a duration of 40ms.
The circuit block diagram (Figure 1) shows the func-
tional blocks consisting of an on-chip oscillator,
counter, exclusive-NOR gate, and D flip-flop. When the
input does not equal the output, the XNOR gate issues
a counter reset. When the switch input state is stable
for the full qualification period, the counter clocks the
flip-flop, updating the output. Figure 2 shows the typical
opening and closing switch debounce operation. On
the MAX6818, the change output (CH) is updated
simultaneously with the switch outputs.
Undervoltage Lockout
The undervoltage lockout circuitry ensures that the out-
puts are at the correct state on power-up. While the sup-
ply voltage is below the undervoltage threshold
(typically 1.9V), the debounce circuitry remains trans-
parent. Switch states are present at the logic outputs
with no debouce delay.
±15kV ESD-Protected, Single/Dual/Octal,
CMOS Switch Debouncers
PIN
2
1, 3
12–19
4, 6
3
2–9
11
1
4
5
20
Pin Description
FUNCTION
Switch Input
Switch Inputs
CMOS Debounced Outputs
CMOS Debounced Output
Switch Inputs
Change-of-State Output. Goes low on switch input change of
state. Resets on EN. Leave unconnected if not used.
Active-Low, Three-State Enable Input for outputs. Resets CH.
Tie to GND to “always enable” outputs.
+2.7V to +5.5V Supply Voltage
NAME
IN
IN1, IN2
OUT8–OUT1
OUT2, OUT1
OUT
IN1–IN8
CH
EN
VCC
VCC
RPU
DQ
R
Q
D
COUNTER
LOAD
OUT
IN
ESD
PROTECTION
UNDER-
VOLTAGE
LOCKOUT
OSC.
MAX6816
MAX6817
MAX6818
Figure 1. Block Diagram
1
2
10
Ground
GND
MAX6816
MAX6817
MAX6818
4
Maxim Integrated
MAX6816/MAX6817/MAX6818
相關PDF資料
PDF描述
MAX7300AAI+T IC I/O EXPANDER I2C 28B 28SSOP
MAX7301AAI+T IC I/O EXPANDER SPI 20B 28SSOP
MAX7310ATE+T IC I/O EXPANDER I2C 8B 16TQFN
MAX7311AUG+T IC I/O EXPANDER I2C 16B 24TSSOP
MAX7312AWG+T IC I/O EXPANDER I2C 16B 24SOIC
相關代理商/技術參數
參數描述
MAX6818EAP/GG8 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6818EAP+ 功能描述:監控電路 Octal Switch Debouncer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6818EAP+ 制造商:Maxim Integrated Products 功能描述:SWITCH ANALOG ((NW))
MAX6818EAP+T 功能描述:監控電路 Octal Switch Debouncer RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX6818EAP-T 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel