- 您現在的位置：買賣IC網 > PDF目錄385546 > MAX6793TP (Maxim Integrated Products, Inc.) High-Voltage, Micropower, Single/Dual Linear Regulators with Supervisory Functions PDF資料下載
參數資料
| 型號： | MAX6793TP |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Voltage, Micropower, Single/Dual Linear Regulators with Supervisory Functions |
| 中文描述： | 高電壓，微功耗，單/雙履行監督職能的線性穩壓器 |
| 文件頁數： | 18/25頁 |
| 文件大?。?/td> | 420K |
| 代理商： | MAX6793TP |
M
High-Voltage, Micropower, Single/Dual Linear
Regulators with Supervisory Functions
18
______________________________________________________________________________________
Selecting Watchdog Timeout Period
The watchdog timeout period is adjustable to accommo-
date a variety of μP applications. With this feature, the
watchdog timeout can be optimized for software execu-
tion. The programmer can determine how often the
watchdog timer should be serviced. Adjust the watch-
dog timeout period (t
WD
) by connecting a capacitor
between CSWT and GND. For normal-mode operation,
calculate the watchdog timeout capacitor as follows:
where t
WD
is in seconds and C
CSWT
is in Farads.
To select the internally fixed watchdog timeout period
for the MAX6791–MAX6794, connect CSWT to OUT1.
To select the internally fixed watchdog timeout period
for the MAX6795/MAX6796, connect CSWT to OUT.
Driving CSWT low disables the watchdog timer.
C
CSWT
must be a low-leakage (< 10nA) type capacitor.
Ceramic capacitors are recommended; do not use
capacitors lower than 100pF to avoid the influence of
parasitic capacitances.
The MAX6791/MAX6792 have a windowed watchdog
timer that asserts
RESET
for t
RP
when the watchdog
recognizes a fast watchdog fault (time between transi-
tions < t
WD1
), or a slow watchdog fault (time between
transitions > t
WD2
). The reset timeout period is adjust-
ed independently of the watchdog timeout period. The
slow watchdog period, t
WD2
, is calculated as follows:
where t
WD2
is in seconds and C
CSWT
is in Farads.
The fast watchdog period, t
WD1
, is selectable as a ratio
from the slow watchdog fault period (t
WD2
). Select the
fast watchdog period by connecting WDS0 and WDS1 to
OUT/OUT1 or GND according to Table 4, which illus-
trates the settings for the 8, 16, and 64 window ratios
(t
WD2
/t
WD1
). For example, if C
CSWT
is 2000pF, and
WDS0 and WDS1 are low, then t
WD2
is 318ms (typ) and
t
WD1
is 40ms (typ).
RESET
asserts if the watchdog input
has two edges too close to each other (faster than t
WD1
);
or has edges that are too far apart (slower than t
WD2
).
All WDI inputs are ignored while
RESET
is asserted. The
watchdog timer begins to count after
RESET
is
deasserted. If the time difference between two transi-
tions on WDI is shorter than t
WD1
or longer than t
WD2
,
RESET
is forced to assert low for the reset timeout peri-
od. If the time difference between two transitions on WDI
is between t
WD1
(min) and t
WD1
(max) or t
WD2
(min)
and t
WD2
(max),
RESET
is not guaranteed to assert or
deassert; see Figure 3. To guarantee that the window
watchdog does not assert
RESET
, strobe WDI between
t
WD1
(max) and t
WD2
(min). The watchdog timer is
cleared when
RESET
is asserted. Disable the watchdog
timer by connecting WDS0 high and WDS1 low.
There are several options available to disable the
watchdog timer (for system development or test pur-
poses or when the μP is in a low-power sleep mode).
One way to disable the watchdog timer is to drive
WD-DIS low for the MAX6793–MAX6796 and drive
WDS0 high and WDS1 low for the MAX6791/MAX6792.
Another method of disabling the watchdog timer is to
pull CSWT low with an open-drain driver stage. This
prevents the capacitor from ramping up. Finally, reduc-
ing the OUT/OUT1 regulator current below the speci-
fied regulator current watchdog-disable threshold (3mA
min) also disables the watchdog timer. The watchdog
t
C
V
A
WD
CSWT
2
6
155
10
×
=
t
C
V
A
WD
CSWT
2
6
155
10
×
=
t
WD1
t
WD2
t
WD0
MIN
GUARANTEED
TO ASSERT
UNDETERMINED
UNDETERMINED
GUARANTEED
TO NOT ASSERT
GUARANTEED
TO ASSERT
FAST
FAULT
NORMAL
OPERATION
SLOW
FAULT
RESET:
WDI INPUT:
MAX
MIN
MAX
Figure 3. Windowed Watchdog Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6794TP | High-Voltage, Micropower, Single/Dual Linear Regulators with Supervisory Functions |
| MAX6803US44D3-T | 4-Pin, Low-Power レP Reset Circuits with Manual Reset |
| MAX6803US46D3-T | 4-Pin, Low-Power レP Reset Circuits with Manual Reset |
| MAX6804US26D3-T | 4-Pin, Low-Power レP Reset Circuits with Manual Reset |
| MAX6804US29D3-T | 4-Pin, Low-Power レP Reset Circuits with Manual Reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6793TPLD0+ | 功能描述:線性穩壓器 - 標準 Dual uPower Linear RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX6793TPLD0+T | 功能描述:線性穩壓器 - 標準 Dual uPower Linear RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX6793TPLD1+ | 功能描述:線性穩壓器 - 標準 Dual uPower Linear RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX6793TPLD1+T | 功能描述:線性穩壓器 - 標準 Dual uPower Linear RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MAX6793TPLD2+ | 功能描述:線性穩壓器 - 標準 Dual uPower Linear RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。