- 您現在的位置：買賣IC網 > PDF目錄385545 > MAX6753KA29 (Maxim Integrated Products, Inc.) UP Reset Circuits with Capacitor-Adjustable Reset/Watchdog Timeout Delay PDF資料下載
參數資料
| 型號： | MAX6753KA29 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | UP Reset Circuits with Capacitor-Adjustable Reset/Watchdog Timeout Delay |
| 中文描述： | 復位電路的電容可調的復位/看門狗超時周期 |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 187K |
| 代理商： | MAX6753KA29 |
M
μP Reset Circuits with Capacitor-Adjustable
Reset/Watchdog Timeout Delay
6
_______________________________________________________________________________________
Pin Description (continued)
PIN
MAX6746
MAX6747
MAX6748
–
MAX6751
MAX6752
MAX6753
NAME
FUNCTION
5
5
—
WDS
Watchdog Select Input. WDS selects the watchdog mode. Connect
WDS to ground to select normal mode and the watchdog timeout
period. Connect WDS to V
CC
to select extended mode, multiplying the
basic timeout period by a factor of 128. A change in the state of WDS
clears the watchdog timer.
—
—
5
SET1
Logic Input. SET1 selects the watchdog window ratio or disables the
watchdog timer. See Table 1.
6
6
6
WDI
Watchdog Input.
MAX6746
–
MAX6751: A falling transition must occur on WDI within the
selected watchdog timeout period or a reset pulse occurs. The
watchdog timer clears when a transition occurs on WDI or whenever
RESET
is asserted. Connect SWT to ground to disable the watchdog
timer function.
MAX6752/MAX6753: WDI falling transitions within periods shorter than
t
WD1
or longer than t
WD2
force
RESET
to assert low for the reset timeout
period. The watchdog timer begins to count after
RESET
is deasserted.
The watchdog timer clears when a valid transition occurs on WDI or
whenever
RESET
is asserted. Connect SET0 high and SET1 low to
disable the watchdog timer function. See the
Watchdog Timer
section.
7
7
7
RESET
Push/Pull or Open-Drain Reset Output.
RESET
asserts whenever V
CC
or
RESET IN drops below the selected reset threshold voltage (V
TH
or
V
RESET IN
, respectively) or manual reset is pulled low.
RESET
remains
low for the reset timeout period after all reset conditions are deasserted,
and then goes high. The watchdog timer triggers a reset pulse (t
RP
)
whenever a watchdog fault occurs.
8
8
8
V
CC
Supply Voltage. V
CC
is the power-supply input and the input for fixed
threshold V
CC
monitor.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6753KA46 | UP Reset Circuits with Capacitor-Adjustable Reset/Watchdog Timeout Delay |
| MAX6770TALD2T | Automotive Micropower Linear Regulators with Supervisor |
| MAX6770TASD2T | Automotive Micropower Linear Regulators with Supervisor |
| MAX6771 | Automotive Micropower Linear Regulators with Supervisor |
| MAX6771TALD2T | Automotive Micropower Linear Regulators with Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6753KA29/V+T | 功能描述:監控電路 Single uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6753KA29+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 2.925V 4.2UA 8PIN SOT-23 - Rail/Tube |
| MAX6753KA29+T | 功能描述:監控電路 Single uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6753KA29-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6753KA30 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。