- 您現在的位置：買賣IC網 > PDF目錄385542 > MAX6701A-07A (Maxim Integrated Products, Inc.) Low-Voltage, SOT23 レP Supervisors with Power- Fail In/Out, Manual Reset, and Watchdog Timer PDF資料下載
參數資料
| 型號： | MAX6701A-07A |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Voltage, SOT23 レP Supervisors with Power- Fail In/Out, Manual Reset, and Watchdog Timer |
| 中文描述： | 低電壓，SOT23封裝的功率Pレ監控失效/輸出，手動復位和看門狗定時器 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 223K |
| 代理商： | MAX6701A-07A |
M
Low-Voltage, SOT23 μP Supervisors with Power-
Fail In/Out, Manual Reset, and Watchdog Timer
8
_______________________________________________________________________________________
Standard- vs. A-Version Comparison
The MAX6701/MAX6702/MAX6703/MAX6705/MAX6706/
MAX6707s
’
WDO
latches low when one of the following
events occurs:
The watchdog timer times out (1.6s, typ).
V
CC
, RST_IN1, or RST_IN2 is below its reset threshold.
MR
is pulled low.
WDO
only deasserts with a valid WDI transition.
TheMAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/
MAX6706(A)/MAX6707(A)s
’
WDO
asserts when either
V
CC
, RST_IN1, or RST_IN2 is below its reset threshold.
WDO
deasserts without a timeout delay when the
undervoltage situation has expired.
WDO
is latched low
when the watchdog timer elapses without seeing a WDI
transition.
WDO
deasserts with a valid WDI transition
OR by pulling
MR
low.
See Figures 4 and 5 for standard-version timing. See
Figures 6 and 7 for A-version timing.
Watchdog Timer
The MAX6701
–
MAX6707 watchdog circuit monitors the
μP
’
s activity. If the μP does not toggle the WDI within 1.6s,
WDO
goes low. When
RESET
is asserted, the watchdog
timer stays cleared and does not count. As soon as reset
is released, the timer starts counting.
WDO
deasserts
after a valid transition is detected at WDI. Pulses as short
as 50ns can be detected.
Typically,
WDO
is connected to the NMI input of a μP.
When V
CC
, RST_IN1, or RST_IN2 drop below the reset
threshold,
WDO
goes low whether or not the watchdog
timer has timed out. Normally this would trigger an NMI,
but
RESET
goes low simultaneously, and thus overrides
the NMI.
The MAX6704 watchdog circuit does not have an inde-
pendent watchdog output (
WDO
). If the μP does not
toggle the watchdog input within 1.6s, the MAX6704
asserts a reset output pulse for the reset timeout period.
Manual Reset
The manual reset input (
MR
) allows reset to be trig-
gered by a pushbutton switch. The switch is effectively
debounced by the reset pulse width.
MR
is CMOS logic
compatible, so it can be driven by an external logic
line.
MR
can be used to force a watchdog timeout to
generate a reset pulse in the MAX6701(A)/MAX6702(A)/
MAX6703(A)/MAX6705(A)/MAX6706(A)/MAX6707(A) by
connecting
WDO
to
MR
.
Power-Fail Comparator
The uncommitted power-fail comparator can be used
for various purposes because its noninverting input and
output are externally available. The inverting input is
internally connected to a 0.62V reference. To build an
early warning circuit for power failure, connect the PFI
pin to a voltage-divider (see
Typical Operating Circuit
).
Choose the voltage-divider ratio so that the voltage at
PFI falls below 0.62V just before the regulator drops
out. Use
PFO
to interrupt the μP so it can prepare for an
orderly power-down. The low-input current at this pin
allows for large resistor values in the divider.
t
WD
t
WD
+5V
0V
WDI
+5V
0V
WDO
+5V
0V
RESET
+5V
0V
(RESET)
t
RP
RESET EXTERNALLY
TRIGGERED BY MR
+5V
0V
MR
( ) ARE FOR MAX6702/MAX6706 ONLY.
t
WDI
t
RP
t
RP
+5V
0V
RESET
WDO
+5V
0V
MR
t
MR
+5V
0V
V
CC
V
TH
V
TH
t
MD
Figure 5. MAX6701/MAX6702/MAX6703/MAX6705/MAX6706/
MAX6707 Watchdog
Figure 6. MAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/
MAX6706(A)/MAX6707(A) RESET, MR, and WDO Timing with
WDI Three-Stated
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6701-08 | Low-Voltage, SOT23 uP Supervisors with Power-Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6701A-03A | Low-Voltage, SOT23 uP Supervisors with Power-Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6705A-07A | Low-Voltage, SOT23 uP Supervisors with Power-Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6701A-KA-T | Low-Voltage, SOT23 uP Supervisors with Power-Fail In/Out, Manual Reset, and Watchdog Timer |
| MAX6701-KA-T | Low-Voltage, SOT23 uP Supervisors with Power-Fail In/Out, Manual Reset, and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6701ALKA | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6701ALKA+ | 制造商:Maxim from Components Direct 功能描述:MAXIM MAX6701ALKA+ PROCESSOR SUPERVISORS - Tape and Reel 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.63V/ADJV/ADJV 12UA 8PIN SOT-23 - Cut Tape Product 制造商:Maxim 功能描述:Maxim MAX6701ALKA+ Processor Supervisors |
| MAX6701ALKA+T | 功能描述:監控電路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6701ALKA-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX6701AMKA | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。