- 您現在的位置：買賣IC網 > PDF目錄1945 > MAX6674ISA+T (Maxim Integrated Products)IC THERMOCOUP TO DGTL 8-SOIC PDF資料下載
參數資料
| 型號： | MAX6674ISA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC THERMOCOUP TO DGTL 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 溫度傳感器 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 3 線 SPI 串行 |
| 電流 - 電源： | 2mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
MAX6674
Cold-Junction-Compensated K-Thermocouple-
to-Digital Converter (0°C to +128°C)
4
_______________________________________________________________________________________
Detailed Description
The MAX6674 is a sophisticated thermocouple-to-digi-
tal converter with a built-in 10-bit analog-to-digital con-
verter (ADC). The device also contains cold-junction
compensation sensing and correction, a digital con-
troller, an SPI-compatible interface, and associated
control logic.
The MAX6674 is designed to work in conjunction with
an external microcontroller (C) or other intelligence in
thermostatic, process-control, or monitoring applica-
tions. The C is typically a power-management or key-
board controller, generating SPI serial commands by
“bit-banging” general-purpose input-output (GPIO) pins
or through a dedicated SPI interface block.
Temperature Conversion
The MAX6674 includes signal conditioning hardware to
convert the thermocouple’s signal into a voltage that is
compatible with the input channels of the ADC. The T+
and T-inputs connect to internal circuitry that reduces the
introduction of noise errors from the thermocouple wires.
Before converting the thermoelectric voltages into
equivalent temperature values, it is necessary to com-
pensate for the difference between the thermocouple
cold-junction side (MAX6674 ambient temperature) and
a 0°C virtual reference.
For a type-K thermocouple, the voltage changes by
41V/°C, which approximates the thermocouple char-
acteristic with the following linear equation:
VOUT = (41V/°C) (TR - TAMB)
where:
VOUT is the thermocouple output voltage (V).
TR is the temperature of the remote point (°C).
TAMB is the ambient temperature (°C).
Cold-Junction Compensation
The function of the thermocouple is to sense a differ-
ence in temperature between two ends. The thermo-
couple’s hot junction can be read from 0°C to
+127.875°C. The cold end (ambient temperature of the
board on which the MAX6674 is mounted) can only
range from -20°C to +85°C. While the temperature at
the cold end fluctuates, the MAX6674 continues to
accurately sense the temperature difference at the
opposite end.
The MAX6674 senses and corrects for the changes in
the ambient temperature with cold-junction compensa-
tion. The device converts the ambient temperature
reading into a voltage using a temperature-sensing
diode. To make the actual thermocouple temperature
measurement, the MAX6674 measures the voltage from
the thermocouple’s output and from the sensing diode.
The device’s internal circuitry passes the diode’s volt-
age (sensing ambient temperature) and thermocouple
voltage (sensing remote temperature minus ambient
temperature) to the conversion function stored in the
ADC to calculate the thermocouple’s hot-junction tem-
perature.
Optimal performance from the MAX6674 is achieved
when the thermocouple cold junction and the device
are at the same temperature. Avoid placing heat-gener-
ating devices or components near the MAX6674
because this may produce cold-junction-related errors.
Digitization
The ADC adds the cold-junction diode measurement
with the amplified thermocouple voltage and reads out
the 10-bit sequence onto the S0 pin. A sequence of all
zeros means the thermocouple reading is 0°C. A
sequence of all ones means the thermocouple reading
is +127.875°C.
Pin Description
PIN
NAME
FUNCTION
1
GND
Ground
2T-
Alumel Lead of Type-K Thermocouple.
Should be connected to ground
externally.
3
T+
Chromel Lead of Type-K Thermocouple
4VCC
Positive Supply. Bypass with a 0.1F
capacitor to GND.
5
SCK
Serial Clock Input
6
CS
Chip Select. Set CS low to enable the
serial interface.
7
S0
Serial Data Output
8
N.C.
No Connection
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6675ISA | IC CONV THERMO TO DIGITAL 8SOIC |
| MAX6682MUA+T | IC THERMISTOR TO DGTL 8UMAX |
| MAX6691MUB+T | IC TEMP-TO-PULSE WIDTH 10-UMAX |
| MAX6818EAP | IC DEBOUNCER SWITCH OCTAL 20SSOP |
| MAX7300AAI+T | IC I/O EXPANDER I2C 28B 28SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6675EVKIT | 功能描述:數據轉換 IC - 多種 RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX6675ISA | 功能描述:數據轉換 IC - 多種 RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX6675ISA+ | 功能描述:數據轉換 IC - 多種 K Thermocouple to Digital Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
| MAX6675ISA+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW)) |
| MAX6675ISA+T | 功能描述:數據轉換 IC - 多種 K Thermocouple to Digital Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 分辨率:8 bit 工作電源電壓:2.7 V to 5.5 V 功耗: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。