- 您現在的位置：買賣IC網 > Datasheet目錄44 > MAX6670AUB45+ (Maxim Integrated)IC TEMP SENSOR REMOTE 10-UMAX Datasheet資料下載
參數資料
| 型號： | MAX6670AUB45+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 5/8頁 |
| 文件大小： | 217K |
| 描述： | IC TEMP SENSOR REMOTE 10-UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 外部 |
| 感應溫度： | 45°C 分界點 |
| 精確度： | ±2.2°C（最小值） |
| 拓?fù)洌?/td> | 風扇控制 |
| 輸出類型： | 數字 |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 管件 |
trip temperature. As the cooling fan operates, the cir-
cuit board temperature should decrease, which causes
the external P-N junctions temperature to decrease.
When the P-N junctions temperature is equal to the trip
threshold minus the hysteresis, the FANOUT pin turns
the fan off, removing power from the fan. For the
MAX6670, HYST is a three-level logic input for control-
ling the fan-drive comparators hysteresis. Connect
HYST to GND to select 4癈 hysteresis, to V
DD
to select
12癈 hysteresis, or leave floating to select 8癈 hystere-
sis. The MAX6668 has a built-in hysteresis of 8癈. This
allows the amount of hysteresis to be matched to the
cooling and noise requirements of the system. Figure 1
shows the temperature trip threshold hysteresis.
Applications Information
Remote-Diode Selection
The MAX6668/MAX6670 directly measure the die tem-
perature of CPUs and other ICs that have on-board tem-
perature-sensing diodes (see Typical Operating Circuit)
or they can measure the temperature of a discrete
diode-connected transistor. For best accuracy, the dis-
crete transistor should be a small-signal device with its
collector and base connected together. Several satisfac-
tory discrete sensing transistors are shown in Table 1.
The sensing transistor must be a small-signal type with
a relatively high forward voltage. Otherwise, the DXP
input voltage range may be violated. The forward volt-
age at the highest expected temperature must be
greater than 0.25V at 10礎, and at the lowest expected
temperature, forward voltage must be less than 0.95V
at 100礎. Do not use large power transistors. Also,
ensure that the base resistance is less than 100&. Tight
specifications for forward current gain (50 < B
F
< 150,
for example) indicate that the manufacturer has good
process controls and that the transistors have consis-
tent V
BE
characteristics.
Noise-Filtering Capacitor
In noisy environments, high-frequency noise can be
attenuated using an external 2200pF capacitor located
at the DXP and DXN pins. Larger capacitor values may
be used for additional filtering, but do not exceed
3300pF; excessive capacitance increases error. Figure
2 shows the recommended DXP/DXN PC traces.
Bypassing and Layout
The location of the remote-sensing junction in the sys-
tem affects the MAX6668/MAX6670s operation. When
using a discrete temperature-sensing transistor, place
the sensing junction close to major heat-generating
components, such as a high-speed CPU or a power
device.
To minimize noise and other errors, follow the guide-
lines below:
1) Place the MAX6668/MAX6670 as close as possible to
the remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 10cm to
20cm (typ) or more as long as the worst noise
sources (such as CRTs, clock generators, memory
buses, and ISA/PCI buses) are avoided. In general,
minimize the distance to the remote-sensing junction.
2) Do not route the DXP/DXN traces next to the deflec-
tion coils of a CRT. Also, do not route the traces
across a fast memory bus, which can introduce
+30癈 error or more, even with good filtering.
3) Route the DXP and DXN traces in parallel and in
close proximity to each other, away from any high-
voltage traces, such as +12VDC. Avoid leakage cur-
rents from PC board contamination, since a 20M&
leakage path from DXP to GND causes about +1癈
error.
4) Connect guard traces to GND on either side of the
DXP/DXN traces (Figure 2). With guard traces in
place, routing near high-voltage traces is no longer
an issue.
5) Route through as few vias and crossunders as possi-
ble to minimize copper/solder thermocouple effects.
6) Use wide traces where possible. Narrow traces are
more inductive and tend to pick up radiated noise.
7) Do not use copper as an EMI shield. Only ferrous
materials such as steel work well. Placing a copper
ground plane between the DXP/DXN traces and
other traces carrying high-frequency noise signals
does not help reduce EMI.
The MAX6668/MAX6670s PGND is the ground return
for the fan driver. Bypass V
DD
to GND with a 1礔
capacitor located as close to V
DD
as possible. Add
additional bypass capacitors for long V
DD
and GND
lines.
Remote Temperature Switches with Integrated
Fan Controller/Driver
_______________________________________________________________________________________ 5
MANUFACTURER
MODEL NO.
Central Semiconductor (USA)
CMPT3904
ON Semiconductor (USA)
2N3904, 2N3906
Rohm Semiconductor (USA)
SST3904
Samsung (Korea)
KST3904-TF
Siemens (Germany)
SMBT3904
Zetex (England)
FMMT3904CT-ND
Table 1. Remote-Sensor Transistor
Manufacturers
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6678AEP92+ | IC TEMP MONITOR 2CH PWM 20-QSOP |
| MAX6681MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6689UP34+ | IC 7CH PREC TEMP MONITOR 20TSSOP |
| MAX6690MEE+ | IC TEMP SENSOR SMBUS 16-QSOP |
| MAX6692YMSA+ | IC SENSOR REMOTE SMBUS 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6670AUB45+ | 功能描述:板上安裝溫度傳感器 Remote Temperature Switch RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6670AUB45+T | 功能描述:板上安裝溫度傳感器 Remote Temperature Switch RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6670AUB45-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6670AUB50 | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6670AUB50+ | 功能描述:板上安裝溫度傳感器 Remote Temperature Switch RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。