- 您現(xiàn)在的位置：買賣IC網 > PDF目錄384691 > MAX6648MUA (MAXIM INTEGRATED PRODUCTS INC) Precision SMBus-Compatible Remote/Local Temperature Sensors with Overtemperature Alarms PDF資料下載
參數資料
| 型號： | MAX6648MUA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Precision SMBus-Compatible Remote/Local Temperature Sensors with Overtemperature Alarms |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 0.80Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MICRO MAX-8 |
| 文件頁數： | 9/17頁 |
| 文件大?。?/td> | 280K |
| 代理商： | MAX6648MUA |
M
Precision SMBus-Compatible Remote/Local
Temperature Sensors with Overtemperature Alarms
_______________________________________________________________________________________
9
rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledge and continues to hold the
ALERT
line low
until cleared. (The conditions for clearing an
ALERT
vary, depending on the type of slave device).
Successful completion of the read alert response proto-
col clears the interrupt latch, provided the condition
that caused the alert no longer exists.
OVERT
Overtemperature Alarm/Warning
Outputs
OVERT
asserts when the temperature rises to a value
stored in one of the
OVERT
limit registers (19h, 20h). It
deasserts when the temperature drops below the
stored limit, minus hysteresis.
OVERT
can be used to
activate a cooling fan, send a warning, invoke clock
throttling, or trigger a system shutdown to prevent com-
ponent damage.
Command Byte Functions
The 8-bit command byte register (Table 5) is the master
index that points to the various other registers within the
MAX6648/MAX6692. The register
’
s POR state is 0000
0000, so a receive byte transmission (a protocol that
lacks the command byte) that occurs immediately after
POR, returns the current local temperature data.
The MAX6648/MAX6692 incorporate collision avoid-
ance so that completely asynchronous operation is
allowed between SMBus operations and temperature
conversions.
One-Shot
The one-shot command immediately forces a new con-
version cycle to begin. If the one-shot command is
received while the MAX6648/MAX6692 are in standby
mode (
RUN
bit = 1), a new conversion begins, after
which the device returns to standby mode. If a one-shot
conversion is in progress when a one-shot command is
received, the command is ignored. If a one-shot com-
mand is received in autonomous mode (
RUN
bit = 0)
between conversions, a new conversion begins, the
conversion rate timer is reset, and the next automatic
conversion takes place after a full delay elapses.
Configuration Byte Functions
The configuration byte register (Table 6) is a read-write
register with several functions. Bit 7 is used to mask (dis-
able) interrupts. Bit 6 puts the MAX6648/MAX6692 into
standby mode (STOP) or autonomous (RUN) mode.
Status Byte Functions
The status byte register (Table 7) indicates which (if
any) temperature thresholds have been exceeded. This
byte also indicates whether the ADC is converting and
whether there is an open-circuit fault detected in the
external sense junction. After POR, the normal state of
all flag bits is zero, assuming no alarm conditions are
present. The status byte is cleared by any successful
read of the status byte, after a conversion is complete
and the fault no longer exists. Note that the
ALERT
interrupt latch is not automatically cleared when the
status flag bit indicating the
ALERT
is cleared. The fault
condition must be eliminated before the
ALERT
output
can be cleared.
When autoconverting, if the T
HIGH
and T
LOW
limits are
close together, it is possible for both high-temp and
low-temp status bits to be set, depending on the
amount of time between status read operations (espe-
cially when converting at the fastest rate). In these cir-
cumstances, it is best not to rely on the status bits to
indicate reversals in long-term temperature changes.
Instead use a current temperature reading to establish
the trend direction.
Conversion Rate Byte
The conversion rate register (Table 8) programs the
time interval between conversions in free-running
autonomous mode (
RUN
= 0). This variable rate control
can be used to reduce the supply current in portable-
BIT
NAME
POR
STATE
FUNCTION
7
RFU
1
Reserved. Always write 1 to
this bit.
6 to 3
RFU
0
Reserved. Always write
zero to this bit.
2
FQ1
0
Fault queue-length control
bit (see Table 4).
1
FQ0
0
Fault queue-length control
bit (see Table 4).
0
RFU
0
Reserved. Always write
zero to this bit.
Table 3. Fault Queue Register Bit Definition
(22h)
FQ1
0
0
1
1
FQ0
0
1
1
0
FAULT QUEUE LENGTH (SAMPLES)
1
2
3
—
Table 4. Fault Queue Length Bit Definition
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6650 | Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface |
| MAX6650EUB | Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface |
| MAX6651 | HEX INVERTERS 20-LCCC -55 to 125 |
| MAX6651EEE | HEX INVERTERS 14-CDIP -55 to 125 |
| MAX6656MEE | PLASTIC ENCAPSULATED DEVICES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX6648MUA+ | 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6648MUA+T | 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6648MUA-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6648YMUA+ | 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX6648YMUA+T | 功能描述:板上安裝溫度傳感器 145C SMBus-Comp Remote/Local Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發(fā)布緊急采購，3分鐘左右您將得到回復。