PECI-to-I2C Translator 13 Maxim Integrated The MAX6618 SCL and SDA lines " />
參數資料
型號： MAX6618AUB+
廠商： Maxim Integrated Products
文件頁數： 5/17頁
文件大?。?/td> 0K
描述： IC PECI TO I2C TRANSLATOR 10UMAX
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
邏輯功能： 變換器
位數： 1
輸入類型： PECL
輸出類型： I²C?
通道數： 1
輸出/通道數目： 1
差分 - 輸入:輸出： 無/無
電源電壓： 3 V ~ 3.6 V
工作溫度： -20°C ~ 120°C
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-µMAX
包裝： 管件
MAX6618
PECI-to-I2C Translator
13
Maxim Integrated
The MAX6618 SCL and SDA lines operate as both
inputs and open-drain outputs. A pullup resistor is
required on SCL and SDA.
Each transmission consists of a START condition sent
by a master, followed by the MAX6618 7-bit slave
address, plus an R/W bit, one or more data bytes, and
finally a STOP condition (Figure 6). To write to a
MAX6618 register, a write transmission consists of a
START condition, followed by the MAX6618 7-bit slave
address plus R/W = 0, a register address byte, one
data byte, and finally a STOP condition. To read from a
MAX6618 register, a combined write and read trans-
missions are required. The first write transmission con-
sists of a START condition, followed by the MAX6618
7-bit slave address plus R/W = 0, a register address
byte, and finally a STOP condition that sets the register
to be read. The second read transmission consists of a
START condition, followed by the MAX6618 7-bit slave
address plus R/W = 1, one or more data bytes, and
finally a STOP condition that reads the data from the
specified register. These write and read transmissions
must be joined using a repeated START without a
STOP after the write transaction, even though the
MAX6618 7-bit slave address needs to be present pre-
ceding the R/W bits.
Start and Stop Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master
has finished communicating with the slave, it issues a
STOP (P) condition by transitioning SDA from low to
high while SCL is high. The bus is then free for another
transmission (Figure 6).
SDA
SCL
START
CONDITION
STOP
CONDITION
S
P
Figure 6. Start and Stop Conditions
SDA
SCL
DATA LINE STABLE;
DATA VALID
CHANGE OF DATA
ALLOWED
Figure 7. Bit Transfer
相關PDF資料
PDF描述
MAX6621AUB+ IC TRANSL PECI TO I2C 10-UMAX
MAX7428EKA+T IC FILTER BUFFER VID SOT23-8
MAX7450ESA+T IC CONDITIONER VIDEO 8-SOIC
MAX7453CSA+ IC FILTER BUFFER VID 8-SOIC
MAX7456EUI+T IC DISPLAY 1CH W/EEPROM 28TSSOP
相關代理商/技術參數
參數描述
MAX6618AUB+ 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+G126 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+T 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+TG11 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MAX6618AUB+TG126 功能描述:接口 - 專用 PECI-to-I2C Translator RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*