參數資料
型號: MAX5841
廠商: Maxim Integrated Products, Inc.
英文描述: 4-Bit Magnitude Comparators 20-LCCC -55 to 125
中文描述: 四路、10位、低功耗、2線、串行電壓輸出DAC
文件頁數: 9/15頁
文件大小: 408K
代理商: MAX5841
M
Quad, 10-Bit, Low-Power, 2-Wire, Serial
Voltage-Output DAC
_______________________________________________________________________________________
9
by a START (S) or REPEATED START (S
r
) condition and
a STOP (P) condition. Each word transmitted over the
bus is 8 bits long and is always followed by an
acknowledge clock pulse.
The MAX5841 SDA and SCL drivers are open-drain
outputs, requiring a pullup resistor to generate, a logic
high voltage (see
Typical Operating Circuit
). Series
resistors R
S
are optional. These series resistors protect
the input stages of the MAX5841 from high-voltage
spikes on the bus lines, and minimize crosstalk and
undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see
START and
STOP Conditions
). Both SDA and SCL idle high when
the I
2
C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA, while SCL is high
(Figure 2). A START condition from the master signals
the beginning of a transmission to the MAX5841. The
master terminates transmission by issuing a not
acknowledge followed by a STOP condition (see
Acknowledge Bit (ACK)
). The STOP condition frees the
bus. If a repeated START condition (S
r
) is generated
instead of a STOP condition, the bus remains active.
When a STOP condition or incorrect address is detect-
ed, the MAX5841 internally disconnects SCL from the
serial interface until the next START condition, minimiz-
ing digital noise and feedthrough.
Early STOP Conditions
The MAX5841 recognizes a STOP condition at any
point during transmission except if a STOP condition
occurs in the same high pulse as a START condition
(Figure 3). This condition is not a legal I
2
C format; at
least one clock pulse must separate any START and
STOP conditions.
Repeated START Conditions
A REPEATED START (S
r
) condition may indicate a
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. S
r
may also be used when the bus
master is writing to several I
2
C devices and does not
want to relinquish control of the bus. The MAX5841 ser-
ial interface supports continuous write operations with
or without an S
r
condition separating them. Continuous
POWER-DOWN
COMMAND BITS
PD1
PD0
MODE/FUNCTION
0
0
Power-up device. DAC output
restored to previous value.
0
1
Power-down mode 0. Power down
device with output floating.
1
0
Power-down mode 1. Power down
device with output terminated with
1k
to GND.
1
1
Power-down mode 2. Power down
device with output terminated with
100k
to GND.
Table 1. Power-Down Command Bits
SCL
SDA
STOP
CONDITION
START
CONDITION
REPEATED START CONDITION
START CONDITION
t
LOW
t
SU, DAT
t
SU, STA
t
SP
t
BUF
t
HD, STA
t
SU, STO
t
R
t
F
t
HD, STA
t
HIGH
t
HD, DAT
Figure 1. 2-Wire Serial Interface Timing Diagram
相關PDF資料
PDF描述
MAX5841LEUB Quad, 10-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC
MAX5842MEUB Quad, 12-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC
MAX5842 4-Bit Magnitude Comparators 16-CDIP -55 to 125
MAX5842LEUB Quad, 12-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC
MAX5858AEVKIT Evaluation Kit for the MAX5858A/MAX5858/MAX5856A
相關代理商/技術參數
參數描述
MAX5841LEUB 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5841LEUB+ 功能描述:數模轉換器- DAC 10-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5841LEUB+T 功能描述:數模轉換器- DAC 10-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5841LEUB-T 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MAX5841MEUB 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube