- 您現在的位置：買賣IC網 > PDF目錄383443 > MAX5822LEUA (MAXIM INTEGRATED PRODUCTS INC) Dual, 12-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC PDF資料下載
參數資料
| 型號： | MAX5822LEUA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DAC |
| 英文描述： | Dual, 12-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC |
| 中文描述： | SERIAL INPUT LOADING, 4 us SETTLING TIME, 12-BIT DAC, PDSO8 |
| 封裝： | MINIATURE, MICRO MAX PACKAGE-8 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 287K |
| 代理商： | MAX5822LEUA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
M
bus is 8 bits long and is always followed by an
acknowledge clock pulse.
The MAX5822 SDA and SCL drivers are open-drain out-
puts, requiring a pullup resistor to generate a logic high
voltage (see the
Typical Operating Circuit
). Series
resistors R
S
are optional. These series resistors protect
the input stages of the MAX5822 from high-voltage
spikes on the bus lines, and minimize crosstalk and
undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see the
START
and STOP Conditions
section). Both SDA and SCL idle
high when the I
2
C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA, while SCL is high
(Figure 2). A START condition from the master signals
the beginning of a transmission to the MAX5822. The
master terminates transmission by issuing a not-
acknowledge followed by a STOP condition (see
Acknowledge Bit (ACK)
). The STOP condition frees the
bus. If a repeated START condition (S
r
) is generated
instead of a STOP condition, the bus remains active.
When a STOP condition or incorrect address is detect-
ed, the MAX5822 internally disconnects SCL from the
serial interface until the next START condition, minimiz-
ing digital noise and feedthrough.
Early STOP Conditions
The MAX5822 recognizes a STOP condition at any
point during transmission except if a STOP condition
occurs in the same high pulse as a START condition
(Figure 3). This condition is not a legal I
2
C format; at
least one clock pulse must separate any START and
STOP conditions.
Repeated START Conditions
A repeated START (S
r
) condition may indicate a
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. S
r
may also be used when the bus
master is writing to several I
2
C devices and does not
want to relinquish control of the bus. The MAX5822 seri-
al interface supports continuous write operations with or
without an S
r
condition separating them. Continuous
read operations require S
r
conditions because of the
change in direction of data flow.
Dual, 12-Bit, Low-Power, 2-Wire, Serial
Voltage-Output DAC
8
_______________________________________________________________________________________
POWER-DOWN
COMMAND BITS
PD1
PD0
MODE/FUNCTION
0
0
Power-up device. DAC output
restored to previous value.
0
1
Power-down mode 0. Power down
device with output floating.
1
0
Power-down mode 1. Power down
device with output terminated with
1k
to GND.
1
1
Power-down mode 2. Power down
device with output terminated with
100k
to GND.
Table 1. Power-Down Command Bits
SCL
SDA
STOP
CONDITION
START
CONDITION
REPEATED START CONDITION
START CONDITION
t
LOW
t
SU, DAT
t
SU, STA
t
SP
t
BUF
t
HD, STA
t
SU, STO
t
F
t
R
t
HD, STA
t
HIGH
t
HD, DAT
Figure 1. 2-Wire Serial Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5841MEUB | Quad, 10-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC |
| MAX5841 | 4-Bit Magnitude Comparators 20-LCCC -55 to 125 |
| MAX5841LEUB | Quad, 10-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC |
| MAX5842MEUB | Quad, 12-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC |
| MAX5842 | 4-Bit Magnitude Comparators 16-CDIP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5822LEUA+ | 功能描述:數模轉換器- DAC 12-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5822LEUA+T | 功能描述:數模轉換器- DAC 12-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5822LEUA-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5822MEUA | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5822MEUA+ | 功能描述:數模轉換器- DAC 12-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。