- 您現在的位置：買賣IC網 > PDF目錄8538 > MAX5811MEUT+T (Maxim Integrated Products)IC DAC SERIAL 10BIT 1CH SOT23-6 PDF資料下載
參數資料
| 型號： | MAX5811MEUT+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/13頁 |
| 文件大小： | 0K |
| 描述： | IC DAC SERIAL 10BIT 1CH SOT23-6 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 設置時間： | 4µs |
| 位數： | 10 |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 727mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-6 |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 1 電壓，單極 |
| 采樣率（每秒）： | * |
MAX5811
10-Bit Low Power 2-Wire Interface Serial,
Voltage-Output DAC
8
_______________________________________________________________________________________
a serial clock line (SCL). The MAX5811 is SMBus com-
patible within the range of VDD = 2.7V to 3.6V. SDA and
SCL facilitate bidirectional communication between the
MAX5811 and the master at rates up to 400kHz. Figure
1 shows the 2-wire interface timing diagram. The
MAX5811 is a transmit/receive slave-only device, rely-
ing upon a master to generate a clock signal. The mas-
ter (typically a microcontroller) initiates data transfer on
the bus and generates SCL to permit that transfer.
A master device communicates to the MAX5811 by
transmitting the proper address followed by command
and/or data words. Each transmit sequence is framed
by a START (S) or REPEATED START (Sr) condition and
a STOP (P) condition. Each word transmitted over the
bus is 8 bits long and is always followed by an
acknowledge clock pulse.
The MAX5811 SDA and SCL drivers are open-drain
outputs, requiring a pullup resistor (500
or greater) to
generate a logic high voltage (see Typical Operating
Circuit). Series resistors RS are optional. These series
resistors protect the input stages of the MAX5811 from
high-voltage spikes on the bus lines, and minimize
crosstalk and undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see START and
STOP Conditions). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
Figure 1. 2-Wire Serial lnterface Timing Diagram
SCL
SDA
STOP
CONDITION
START
CONDITION
REPEATED START CONDITION
START CONDITION
tLOW
tSU, DAT
tSU, STA
tSP
tBUF
tHD, STA
tSU, STO
tR
tF
tHD, STA
tHIGH
tHD, DAT
SCL
SDA
SSr
P
Figure 2. START/STOP Conditions
Figure 3. Early STOP Condition
SCL
SDA
STOP
START
SCL
SDA
ILLEGAL
STOP
START
ILLEGAL EARLY STOP CONDITION
LEGAL STOP CONDITION
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B31-MU-F1 | CONVERTER MOD DC/DC 12V 200W |
| LT1189CS8 | IC AMP VIDEO DIFFRNC ADJ 8-SOIC |
| MAX5811LEUT+T | IC DAC SERIAL 10BIT 1CH SOT23-6 |
| VE-B3R-MU-F4 | CONVERTER MOD DC/DC 7.5V 200W |
| VI-B4K-MX-S | CONVERTER MOD DC/DC 40V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5811NEUT | 制造商:Maxim Integrated Products 功能描述:10-BIT LOW-POWER 2-WIRE SERIAL V - Cut Tape Product |
| MAX5811NEUT+T | 功能描述:數模轉換器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩(wěn)定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5811NEUT-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩(wěn)定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5811PEUT | 制造商:Maxim Integrated Products 功能描述:10-BIT LOW-POWER 2-WIRE SERIAL V - Rail/Tube |
| MAX5811PEUT+T | 功能描述:數模轉換器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩(wěn)定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。