- 您現在的位置：買賣IC網 > PDF目錄2089 > MAX5486EUG+ (Maxim Integrated Products)IC CNTRL VOL STEREO 24TSSOP PDF資料下載
參數資料
| 型號： | MAX5486EUG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CNTRL VOL STEREO 24TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 62 |
| 類型： | 立體聲音量控制 |
| 應用： | 車載系統，臺式音頻，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
MAX5486
Stereo Volume Control with Pushbutton
Interface
_______________________________________________________________________________________
7
_______________________________________________________________________________________
7
Pin Description
PIN
NAME
FUNCTION
1VLOGIC
Digital Logic Power Supply. Bypass VLOGIC to ground with a 0.1F capacitor as close as possible to
the device.
2
DN/BALR
Active-Low Downward Volume/Balance Control. Press DN/BALR to decrease the volume in volume
mode and move balance to the right in balance mode. DN/BALR is internally pulled high with a
resistor to VLOGIC.
3
UP/BALL
Active-Low Upward Volume/Balance Control. Press UP/BALL to increase the volume in volume mode
and move balance to the left in balance mode. UP/BALL is internally pulled high with a resistor to
VLOGIC.
4
MUTE
Active-Low Mute Input. Pull MUTE low to toggle the wiper between the mute setting (see Table 1) and
the current setting. MUTE is internally pulled up to VLOGIC with a resistor.
5
MODE
Active-Low Volume/Balance Control Input. Each high-to-low transition on MODE toggles between the
volume and balance modes. MODE is pulled high internally with a resistor to VLOGIC. On power-up,
the MAX5486 is in volume control mode.
6
SHDN
Active-Low Shutdown Input. Drive SHDN low to place the device in shutdown mode. In shutdown
mode, the MAX5486 stores the last wiper settings. The wipers move to the L_ end of the resistor
string. Terminating the shutdown mode restores the wipers to the previous settings.
7
N.C.
Internally connected. Leave unconnected.
8
HR
Potentiometer R High Terminal
9
LR
Potentiometer R Low Terminal
10
WR
Potentiometer R Wiper Buffered Output
11
BIAS
Midbias Voltage Output. VBIAS = (VDD + VSS) / 2; connect a 100pF capacitor from BIAS to VSS.
12
BIASCAP
Bias Generator Bypass. Connect a 1F filter capacitor from BIASCAP to VSS.
13
VDD
Analog Power Supply. Bypass VDD to ground with a 0.1F capacitor as close as possible to the
device.
14
VSS
Negative Power Supply. Bypass VSS to ground with a 0.1F capacitor as close as possible to the
device. Connect to GND for single supply operation.
15
WL
Potentiometer L Wiper Buffered Output
16
LL
Potentiometer L Low Terminal
17
HL
Potentiometer L High Terminal
18–22
LEDIND0–
LEDIND4
LED Indicator Open-Drain Output 0–LED Indicator Open-Drain Output 4. Connect a 1M
Ω resistor
from LEDIND4 to VLOGIC to enable these LED inductor drivers. LEDIND0–LEDIND4 form a bar graph
indication of the current volume or balance. In volume mode, all LEDs off indicate mute and all LEDs
on indicate maximum volume. In balanced mode, LED2 on indicates centered or balanced. Connect
LEDIND0–LEDIND4 to GND when LED indicator drivers are not used.
23
MODEIND
Active-Low Volume-Control/Balance-Control Mode-Indicator Open-Drain Output. Connect to an LED
through a resistor to VLOGIC. When the LED is on, the MAX5486 is in balance-control mode. When the
LED is off, the MAX5486 is in volume-control mode.
24
GND
Ground
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5679ETJ+T | IC GENERATOR PROG LCD 32TQFN |
| MAX6618AUB+ | IC PECI TO I2C TRANSLATOR 10UMAX |
| MAX6621AUB+ | IC TRANSL PECI TO I2C 10-UMAX |
| MAX7428EKA+T | IC FILTER BUFFER VID SOT23-8 |
| MAX7450ESA+T | IC CONDITIONER VIDEO 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5486EUG+ | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5486EUG+T | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE | 制造商:Maxim Integrated Products 功能描述:DUAL 256-TAP SPI 10K DIGITAL POTENTIOMETER - Rail/Tube |
| MAX5487ETE#G16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE#TG16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。