- 您現在的位置：買賣IC網 > PDF目錄385534 > MAX5486 (Maxim Integrated Products, Inc.) Stereo Volume Control with Pushbutton Interface PDF資料下載
參數資料
| 型號： | MAX5486 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Stereo Volume Control with Pushbutton Interface |
| 中文描述： | 立體聲音量控制，提供按鍵接口 |
| 文件頁數： | 10/16頁 |
| 文件大小： | 232K |
| 代理商： | MAX5486 |
M
wiper changes position, the second wiper has 126ms
to change or it changes automatically.
Power-On Reset
The power-on comparators monitor (V
DD
- V
SS
) and
(V
LOGIC
- GND). A power-on reset is initiated when
either of the supplies is brought back to the normal
operating voltage. The power-on reset feature sets both
wipers to -12dB. The wipers initially wake up in mute
mode (-90dB) and move to the -12dB position when
V
H
= V
L
to eliminate clicks and pops during power-up.
With DC inputs at V
H
and V
L
, the wipers move after
exceeding the timeout period. A power-on reset places
the MAX5486 in volume-control mode.
Shutdown (
SHDN
)
Upon entering shutdown, the MAX5486 stores the last
wiper settings. The wipers move to the L_ end of the
resistor string when V
H
= V
L
to eliminate clicks and
pops during shutdown. With DC inputs at V
H
and V
L
,
the wipers move after exceeding the timeout period.
Exiting shutdown restores the wipers to their previous
settings. Shutdown also turns off all the LED indicators
to save power.
Mute Function (
MUTE
)
The MAX5486 features a mute function input,
MUTE
.
Successive low pulses on
MUTE
toggle its setting.
Activating the mute function forces both wipers to maxi-
mum attenuation (-90dB typ). Deactivating the mute
function returns the wipers to their previous settings.
MUTE
is internally pulled high with a resistor to V
LOGIC
.
When both wipers are in the tap 31 position
(-62dB attenuation) further commands to lower the vol-
ume place the wipers in the mute position (see Table 1).
Mode Indicator (
MODEIND
)
The open-drain
MODEIND
indicates volume-control
mode or balance-control mode for the MAX5486.
Connect
MODEIND
to an LED with a series resistor to
V
LOGIC
. When the LED is on, the MAX5486 is in bal-
ance-control mode. When the LED is off, the MAX5486
is in volume-control mode. See the Mode Control
(
MODE
) section for more detail on switching between
modes.
Level Indicator LEDs
The MAX5486 includes five indicator LED drivers to dis-
play the current wiper settings in either volume or bal-
ance mode. The LED indicators are enabled by
connecting a 1M
Ω
resistor between LEDIND4 and
V
LOGIC
. Connect the LEDIND_ outputs to the LEDs and
to V
LOGIC
through a series resistor as shown in the
Typical Operating Circuit Connect LEDIND_ outputs to
GND when LED indicator drivers are not used.
In volume-control mode, all LEDs are off when the
wipers reach the highest attenuation levels (mute). All
LEDs are on at the lowest attenuation levels (0dB).
Stereo Volume Control with Pushbutton
Interface
10
______________________________________________________________________________________
(3a)
WR
H_
L_
H_
L_
WL
WR
WR
WL
WL
WR
WL
WR
WR
WL
WL
(3b)
VOLUME LEVEL IS SET
VOLUME LEVEL MAINTAINED
BALANCE SHIFTS TO WL
VOLUME LEVEL MAINTAINED
BALANCE SHIFTS TO WL
VOLUME LEVEL IS SET BY WR
PRESS BALL
ONCE
PRESS BALL
ONCE
PRESS BALL
ONCE
PRESS BALL
ONCE
Figures 3a and 3b. Balance-Control Operation
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5494 | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5494ETE | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5495 | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5495ETE | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5496 | 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5486EUG+ | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5486EUG+T | 功能描述:數字電位計 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE | 制造商:Maxim Integrated Products 功能描述:DUAL 256-TAP SPI 10K DIGITAL POTENTIOMETER - Rail/Tube |
| MAX5487ETE#G16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5487ETE#TG16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。