- 您現在的位置：買賣IC網 > PDF目錄383439 > MAX5478 (Maxim Integrated Products, Inc.) Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers PDF資料下載
參數資料
| 型號： | MAX5478 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 通用總線功能 |
| 英文描述： | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| 中文描述： | 雙路、256抽頭、非易失、I2C接口、數字電位器 |
| 文件頁數： | 4/15頁 |
| 文件大?。?/td> | 383K |
| 代理商： | MAX5478 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
M
Dual, 256-Tap, Nonvolatile, I
2
C-Interface,
Digital Potentiometers
4
_______________________________________________________________________________________
Note 1:
Note 2:
All devices are production tested at T
A
= +25°C and are guaranteed by design and characterization for -40°C < T
A
< +85°C.
The DNL and INL are measured with the potentiometer configured as a voltage-divider with H_ = V
DD
and L_ = GND. The
wiper terminal is unloaded and measured with a high-input-impedance voltmeter.
The DNL and INL are measured with the potentiometer configured as a variable resistor. H_ is unconnected and L_ =
GND. For V
DD
= +5V, the wiper is driven with 400μA (MAX5477), 80μA (MAX5478), or 40μA (MAX5479). For V
DD
= +3V,
the wiper is driven with 200μA (MAX5477), 40μA (MAX5478), or 20μA (MAX5479).
The wiper resistance is measured using the source currents given in Note 3.
The devices draw current in excess of the specified supply current when the digital inputs are driven with voltages between
(V
DD
- 0.5V) and (GND + 0.5V). See Supply Current vs. Digital Input Voltage in the
Typical Operating Characteristics
.
Wiper at midscale with a 10pF load (DC measurement). L_ = GND, an AC source is applied to H_, and the W_ output is
measured. A 3dB bandwidth occurs when the AC W_/H_ value is 3dB lower than the DC W_/H_ value.
The programming current exists only during power-up and EEPROM writes.
The SCL clock period includes rise and fall times (t
R
= t
F
). All digital input signals are specified with t
R
= t
F
= 2ns and
timed from a voltage level of (V
IL
+ V
IH
) / 2.
Digital timing is guaranteed by design and characterization, and is not production tested.
Note 10:
This is measured from the STOP pulse to the time it takes the output to reach 50% of the output step size (divider mode). It
is measured with a maximum external capacitive load of 10pF.
Note 11:
An appropriate bus pullup resistance must be selected depending on board capacitance. Refer to the I
2
C-bus specifica-
tion document linked to this web address: www.semiconductors.philips.com/acrobat/literature/9398/39340011.pdf
Note 12:
The idle time begins from the initiation of the STOP pulse.
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
PARAMETER
SYMBOL
t
HIGH
t
LOW
t
SU:DAT
t
HD:DAT
t
R
t
F
t
SU:STO
CONDITIONS
MIN
0.6
1.3
100
0
TYP
MAX
UNITS
μs
μs
ns
μs
ns
ns
μs
SCL High Time
SCL Low Time
Data Setup Time
Data Hold Time
SDA, SCL Rise Time
SDA, SCL Fall Time
Setup Time for STOP Condition
0.9
300
300
0.6
Bus Free Time Between STOP
and START Condition
t
BUF
Minimum power-up rate = 0.2V/μs
1.3
μs
Pulse Width of Spike Suppressed
t
SP
50
ns
Capacitive Load for Each Bus
Line
C
B
(Note 11)
400
pF
Write NV Register Busy Time
(Note 12)
12
ms
TIMING CHARACTERISTICS (continued)
(V
DD
= +2.7V to +5.25V, H_ = V
DD
, L_ = GND, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at V
DD
= +5V,
T
A
= +25°C. See Figure 1.) (Notes 8 and 9)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5478ETE | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5478EUD | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5479 | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5479EUD | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX547AEQH | Octal, 13-Bit Voltage-Output DAC with Parallel Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5478ETD | 制造商:Maxim Integrated Products 功能描述:DUAL, 256-TAP, NONVOLATILE, I2C-INTERFACE, DI - Rail/Tube |
| MAX5478ETE | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5478ETE#G16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5478ETE#TG16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5478ETE+ | 功能描述:數字電位計 IC Dual 256-Tap NV I2C-Interface RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。