- 您現在的位置：買賣IC網 > PDF目錄383438 > MAX5477-MAX5479 (Maxim Integrated Products, Inc.) Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers PDF資料下載
參數資料
| 型號： | MAX5477-MAX5479 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 通用總線功能 |
| 英文描述： | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| 中文描述： | 雙路、256抽頭、非易失、I2C接口、數字電位器 |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 383K |
| 代理商： | MAX5477-MAX5479 |
M
Dual, 256-Tap, Nonvolatile, I
2
C-Interface,
Digital Potentiometers
______________________________________________________________________________________
11
slave address is the NOP/
W
bit. Set the NOP/
W
bit low for
a write command and high for a no-operation command.
The MAX5477/MAX5478/MAX5479 provide three
address inputs (A0, A1, and A2), allowing up to eight
devices to share a common bus (Table 1). The first 4
bits (MSBs) of the MAX5477/MAX5478/MAX5479 slave
addresses are always 0101. A2, A1, and A0 set the next
3 bits in the slave address. Connect each address input
to V
DD
or GND to set these 3 bits. Each device must
have a unique address to share a common bus.
Message Format for Writing
Write to the MAX5477/MAX5478/MAX5479 by transmit-
ting the device’s slave address with NOP/
W
(8th bit) set
to zero, followed by at least 1 byte of information
(Figure 7). The 1st byte of information is the command
byte. The bytes received after the command byte are
the data bytes. The 1st data byte goes into the internal
register of the MAX5477/MAX5478/MAX5479 as select-
ed by the command byte (Figure 8).
Command Byte
Use the command byte to select the source and desti-
nation of the wiper data (nonvolatile or volatile memory
registers) and swap data between nonvolatile and
volatile memory registers (see Table 2).
Command Descriptions
VREG: The data byte writes to the volatile memory reg-
ister and the wiper position updates with the data in the
volatile memory register.
NVREG: The data byte writes to the nonvolatile memory
register. The wiper position is unchanged.
NVREGxVREG: Data transfers from the nonvolatile
memory register to the volatile memory register (wiper
position updates).
VREGxNVREG: Data transfers from the volatile memory
register into the nonvolatile memory register.
Nonvolatile Memory
The internal EEPROM consists of a 16-bit nonvolatile
register that retains the value written to it prior to power
down. The nonvolatile register is programmed with the
midscale value at the factory. The nonvolatile memory
is guaranteed for 50 years for wiper position retention
and up to 200,000 wiper write cycles. A write-protect
feature prevents accidental overwriting of the EEPROM.
Connect WP to V
DD
or leave open to enable the write-
protect feature. The wiper position only updates with
the value in the EEPROM when WP = V
DD
. Connect WP
to GND to allow EEPROM write cycles and to update
the wiper position from nonvolatile memory or directly
from the I
2
C serial interface.
Power-Up
Upon power-up, the MAX5477/MAX5478/MAX5479
load the data stored in the nonvolatile memory register
into the volatile memory register, updating the wiper
position with the data stored in the nonvolatile memory
register. This initialization period takes 10μs.
A
0
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
NOP/W
1 BYTE
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
D15
D14 D13 D12 D11 D10
D9
D8
D1
D0
D3
D2
D5
D4
D7
D6
HOW CONTROL BYTE AND DATA BYTE MAP INTO
MAX5477/MAX5478/MAX5479 REGISTERS
S
A
A
P
S
A
0
SLAVE ADDRESS
COMMAND BYTE
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
NOP/W
ACKNOWLEDGE FROM
MAX5477/MAX5478/MAX5479
D15
D14
D13
D12
D11
D10
D9
D8
COMMAND BYTE IS STORED ON RECEIPT OF STOP CONDITION
A
P
Figure 7. Command Byte Received
Figure 8. Command and Single Data Byte Received
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5477ETE | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5477EUD | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5479ETE | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5478 | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
| MAX5478ETE | Dual, 256-Tap, Nonvolatile, I2C-Interface, Digital Potentiometers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5478ETD | 制造商:Maxim Integrated Products 功能描述:DUAL, 256-TAP, NONVOLATILE, I2C-INTERFACE, DI - Rail/Tube |
| MAX5478ETE | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5478ETE#G16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5478ETE#TG16 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5478ETE+ | 功能描述:數字電位計 IC Dual 256-Tap NV I2C-Interface RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。