- 您現在的位置：買賣IC網 > PDF目錄9188 > MAX5395LATA+T (Maxim Integrated Products)IC DGTL POT 256POS 10KOHM 8TDFN PDF資料下載
參數資料
| 型號： | MAX5395LATA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT 256POS 10KOHM 8TDFN |
| 標準包裝： | 2,500 |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 50 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C |
| 電源電壓： | 1.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
12
Maxim Integrated
MAX5395
Single, 256-Tap Volatile, I2C, Low-Voltage Linear
Taper Digital Potentiometer
In read mode, the master pulls down SDA during the
9th clock cycle to acknowledge receipt of data from the
MAX5395. An acknowledge is sent by the master after
each read byte to allow data transfer to continue. A not-
acknowledge is sent when the master reads the final byte
of data from the MAX5395, followed by a STOP condition.
I2C Slave Address
The slave address is defined as the seven most signifi-
cant bits (MSBs) followed by the R/W bit. See Figure 5
and Figure 6. The five most significant bits are 01010
with the 3 LSBs determined ADDR0 as shown in Table 1.
Setting the R/W bit to 1 configures the MAX5395 for read
mode. Setting the R/W bit to 0 configures the MAX5395
for write mode. The slave address is the first byte of infor-
mation sent to the MAX5395 after the START condition.
The MAX5395 has the ability to detect an unconnected
(N.C.) state on the ADDR0 input for additional address
flexibility; if disconnecting the ADDR0 input, be certain to
minimize all loading on the ADDR0 input (i.e. provide a
landing for ADDR0, but do not allow any board traces).
I2C Message Format for Writing
A master device communicates with the MAX5395 by
transmitting the proper slave address followed by com-
mand and data word. Each transmit sequence is framed
by a START or Repeated START condition and a STOP
condition as described above. Each word is 8 bits long
and is always followed by an acknowledge clock (ACK)
pulse as shown in Figure 5. The first byte contains the
address of the MAX5395 with R/W = 0 to indicate a write.
The second byte contains the command to be executed
and the third byte contains the data to be written.
I2C Message Format for Readback Operations
Each readback sequence is framed by a START or
Repeated START condition and a STOP condition. Each
word is 8 bits long and is followed by an acknowledge
clock pulse as shown in Figure 6. The first byte contains
the address of the MAX5395 with R/W = 0 to indicate a
write. The second byte contains the register that is to
be read back. There is a Repeated START condition,
followed by the device address with R/W = 1 to indicate
Figure 4. I2C Acknowledge
Figure 5. I2C Complete Write Serial Transmission
Table 1. I2C Slave Address LSBs
N.C. = No connection.
ADDR0
A1
A0
SLAVE ADDRESS
GND
0
0101000
N.C.
0
1
0101001
VDD
1
0101011
1
SCL
START
CONDITION
SDA
29
CLOCK PULSE
FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
01 01 0A1A0W
D D D D D D D D
AA
A
SEE REGISTER OPTIONS
SDA
START
STOP
WRITE ADDRESS
BYTE #1: I2C SLAVE ADDRESS
WRITE REGISTER
BYTE #2: REG # = N
WRITE DATA
BYTE #3: DATA BYTE B[7:0]
SCL
REG N UPDATED
ACK. GENERATED BY MAX5395L/
MAX5395M/MAX5395N
ACK. GENERATED BY I2C MASTER
相關PDF資料 |
PDF描述 |
|---|---|
| V24A48H300BL3 | CONVERTER MOD DC/DC 48V 300W |
| MS3450L28-9PY | CONN RCPT 12POS WALL MNT W/PINS |
| MS3450L28-9PX | CONN RCPT 12POS WALL MNT W/PINS |
| V24A48H300BL2 | CONVERTER MOD DC/DC 48V 300W |
| MAX5394MATA+T | IC DGTL POT 256POS 50KOHM 8TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5395MATA+T | 功能描述:數字電位計 IC Sgl 256-tap Volatile DigiPot w/SPI RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5395NATA+T | 功能描述:數字電位計 IC Sgl 256-tap Volatile DigiPot w/SPI RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX539ACPA | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX539ACPA+ | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX539ACSA | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。