- 您現在的位置：買賣IC網 > PDF目錄384687 > MAX538BESA (MAXIM INTEGRATED PRODUCTS INC) +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs PDF資料下載
參數資料
| 型號： | MAX538BESA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | DAC |
| 英文描述： | +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs |
| 中文描述： | SERIAL INPUT LOADING, 25 us SETTLING TIME, 12-BIT DAC, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 207K |
| 代理商： | MAX538BESA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Internal Reference (MAX 531 only)
The on-chip reference is lesser trimmed to generate 2.048V
at REFOUT. The output stage can source and sink current,
so REFOUT can settle to the correct voltage quickly in
response to code-dependent loading changes. Typically,
source current is 5mA and sink current is 100μA.
REFOUT connects the internal reference to the R-2R DAC
ladder at REFIN. The R-2R ladder draws 50μA maximum
load current. If any other connection is made to REFOUT,
ensure that the total load current is less than 100μA to
avoid gain errors.
For applications requiring very low-noise performance,
connect a 33μF capacitor from REFOUT to AGND. If noise
is not a concern, a lower value capacitor (3.3μF min) may
be used. To reduce noise further, insert a buffered RC filter
between REFOUT and REFIN (Figure 2). The reference
bypass capacitor, C
REFOUT
, is still required for reference
stability. In applications not requiring the reference, con-
nect REFOUT to V
DD
or use the MAX538 or MAX539 (no
internal reference).
External Reference
An external reference in the range (V
SS
+ 2V) to (V
DD
- 2V)
may be used with the MAX531 in dual-supply operation.
With the MAX538/MAX539 or the MAX531 in single-supply
use, the reference must be positive and may not exceed
V
DD
- 2V. The reference voltage determines the DAC’s full-
scale output. The DAC input resistance is code dependent
and is minimum (40k
) at code 555 hex and virtually infi-
nite at code 000 hex. REFIN’s input capacitance is also
code dependent and has a 50pF maximum value at sever-
al codes. Because of the code-dependent nature of refer-
ence input impedances, a high-quality, low-output-imped-
ance amplifier (such as the MAX480 low-power, precision
op amp) should be used.
If an upgrade to the internal reference is required, the 2.5V
MAX873A is suitable: ±15mV initial accuracy, TCV
OUT
=
7ppm/°C (max).
Logic Interface
The MAX531/MAX538/MAX539 logic inputs are designed to
be compatible with TTL or CMOS logic levels. However, to
achieve the lowest power dissipation, drive the digital inputs
with rail-to-rail CMOS logic. With TTL logic levels, the power
requirement increases by a factor of approximately 2.
Serial Clock and Update Rate
Figure 1 shows the MAX531/MAX538/MAX539 timing. The
maximum serial clock rate is given by 1 / (t
CH
+ t
CL
),
approximately 14MHz. The digital update rate is limited by
the chip-select period, which is 16 x (t
CH
+ t
CL
) + t
CSW
.
This equals a 1.14μs, or 877kHz, update rate. However, the
DAC settling time to 12 bits is 25μs, which may limit the
update rate to 40kHz for full-scale step transitions.
____________Applications Information
Refer to Figures 3a and 3b for typical operating connec-
tions.
Serial Interface
The MAX531/MAX538/MAX539 use a three-wire serial
interface that is compatible with SPI , QSPI
(CPOL = CPHA = 0), and Microwire standards as shown
in Figures 4 and 5. The DAC is programmed by writing two
8-bit words (see Figure 1 and the Functional Diagram.
Sixteen bits of serial data are clocked into the DAC MSB
first with the MSB preceded by four fill (dummy) bits. The
four dummy bits are not normally needed. They are
required
only
when DACs are daisy-chained. Data is
clocked in on SCLK’s rising edge while CS is low. The seri-
al input data is held in a 16-bit serial shift register. On CS’s
rising edge, the 12 least significant bits are transferred to
the DAC register and update the DAC. With CS high, data
cannot be clocked into the MAX531/MAX538/MAX539.
The MAX531/MAX538/MAX539 input data in 16-bit blocks.
The SPI and Microwire interfaces output data in 8-bit
blocks, thereby requiring two write cycles to input data to
the DAC. The QSPI interface allows variable data input
from eight to 16 bits, and can be loaded into the DAC in
one write cycle.
M
+5V, Low-Power, Voltage-Output,
S erial 12-Bit DACs
_______________________________________________________________________________________
9
300
50
1
10
100
100
M
FREQUENCY (kHz)
R
μ
V
R
)
150
200
250
0
0.1
1000
TOTAL
REFERENCE
NOISE
R
S
REFOUT
C
REFOUT
C
S
TEK 7A22
C
REFOUT
= 3.3
μ
F
C
REFOUT
= 47
μ
F
SINGLE-POLE ROLLOFF
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
R
Figure 2. Reference Noise vs. Frequency
SPI and QSPI are trademarks of Motorola, Inc.
Microwire is a trademark of National Semiconductor Corp.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX539ACPA | +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs |
| MAX539ACSA | +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs |
| MAX539AESA | +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs |
| MAX539BCPA | +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs |
| MAX539BCSA | +5V, Low-Power, Voltage-Output, Serial 12-Bit DACs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX538BESA+ | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX538BESA+T | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX538BESA-T | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5391LATE+ | 功能描述:數字電位計 IC Dl 256-Tap Volatile Linear Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MAX5391LATE+T | 功能描述:數字電位計 IC Dl 256-Tap Volatile Linear Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。