- 您現在的位置：買賣IC網 > PDF目錄3276 > MAX5165NCCM+ (Maxim Integrated Products)IC AMP SAMPLE/HOLD 32CH 48-LQFP PDF資料下載
參數資料
| 型號： | MAX5165NCCM+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 250 |
| 放大器類型： | 采樣和保持 |
| 電路數： | 32 |
| 電流 - 輸入偏壓： | 1µA |
| 電壓 - 輸入偏移： | 5000µV |
| 電流 - 電源： | 36mA |
| 電流 - 輸出 / 通道： | 2mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
Sample Mode
Driving M3–M0 low (one at a time) selects sample
mode (Tables 1, 2). During sample mode, the selected
multiplexer channel connects to IN, allowing the hold
capacitor to acquire the input signal. To guarantee an
accurate sample, maintain sample mode for at least
4s. The output of the S/H amplifier tracks the input
after 4s. Only the addressed channel on the selected
multiplexer samples the input; all other channels remain
in hold mode.
Hold Mode
Driving M3–M0 high selects hold mode. Hold mode dis-
ables the multiplexer and disconnects all eight chan-
nels on the 1-to-8 multiplexer from the input. When a
channel is disconnected, the hold capacitor maintains
the sampled voltage at the output with a 1mV/sec
droop rate (towards VDD).
Hold Step
When switching between sample mode and hold mode,
the voltage of the hold capacitor changes due to
charge injection from stray capacitance. This voltage
change, called hold step, is minimized by limiting the
amount of stray capacitance seen by the hold capaci-
tor. The MAX5165 limits the hold step to 0.25mV (typ).
An output capacitor to ground can be used to filter out
this small hold-step error.
Output
The MAX5165 contains an output buffer for each multi-
plexer channel (32 total), so the hold capacitor sees a
high-impedance input, reducing the droop rate. The
capacitor droops at a 1mV/sec (typ) rate while in hold
mode. The buffer also provides a low output imped-
ance; however, the device contains output resistors in
series with the buffer output (Figure 1) for selected out-
put filtering. To provide greater design flexibility, the
MAX5165 is available with an RO of 50
, 500, or 1k.
Note: Output loads increase the analog supply cur-
rent (IDD and ISS). Excessive loading of the output(s)
damages the device by consuming more power than the
device will dissipate (see Absolute Maximum Ratings).
The resistor-divider formed by the output resistor (ROUT)
and load impedance (RL) scales the sampled voltage
(VSAMP). Determine the output voltage (VOUT_) as follows:
Voltage Gain = AV = RL / (RL + ROUT)
VOUT_ = VSAMP AV
The maximum output voltage range depends on the
analog supply voltages available, and the scaling factor
used:
(VSS + 0.75V) AV
≤ VOUT_ ≤ (VDD - 2.4V) AV
when RL =
∞, then AV = 1 and this equation becomes:
(VSS + 0.75V)
≤ VOUT ≤ (VDD - 2.4V)
MAX5165
32-Channel Sample/Hold Amplifier
with a Single Multiplexed Input
_______________________________________________________________________________________
7
0
Table 1. Output Selection
Table 2. Mode Selection
0
1
0
1
0
1
ADDRESS
0
1
0
1
OUT2
OUT3
OUT6
OUT0
OUT7
OUT1
OUT4
OUT5
OUT10
OUT11
OUT14
OUT8
OUT15
OUT9
OUT12
OUT13
OUT18
OUT19
OUT22
OUT16
OUT23
OUT17
OUT20
OUT21
OUTPUT SELECTED
OUT26
OUT27
OUT30
OUT24
OUT31
OUT25
OUT28
OUT29
A2
A1
A0
MUX0
MUX1
MUX2
MUX3
0 = Logic Low, 1 = Logic High
0
1
Sample mode enabled on selected
analog multiplexer and channel
(Table 1).
Hold mode enabled on selected
analog multiplexer and channel
(Table 1).
MODE-SELECT
INPUTS (M3–M0)
ACTION
0 = Logic Low, 1 = Logic High
* Only one M_ input asserted low; all others must be logic high
to meet the timing specification (see Single vs. Simultaneous
Sampling section).
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5165NECM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5165MECM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5167NCCM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5168MCCM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5168NCCM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5165NCCM+ | 功能描述:采樣&保持放大器 32Ch Sample/Hold Amp RoHS:否 制造商:Texas Instruments 通道數量:2 捕獲時間:20 us 電源電壓-最大:18 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格: 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5165NCCM+T | 功能描述:采樣&保持放大器 32Ch Sample/Hold Amp RoHS:否 制造商:Texas Instruments 通道數量:2 捕獲時間:20 us 電源電壓-最大:18 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格: 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5165NCCM-T | 功能描述:采樣&保持放大器 RoHS:否 制造商:Texas Instruments 通道數量:2 捕獲時間:20 us 電源電壓-最大:18 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格: 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5165NECM | 功能描述:采樣&保持放大器 RoHS:否 制造商:Texas Instruments 通道數量:2 捕獲時間:20 us 電源電壓-最大:18 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格: 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5165NECM+ | 功能描述:采樣&保持放大器 32Ch Sample/Hold Amp RoHS:否 制造商:Texas Instruments 通道數量:2 捕獲時間:20 us 電源電壓-最大:18 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 安裝風格: 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。