- 您現在的位置：買賣IC網 > PDF目錄8934 > MAX5138BGTE+ (Maxim Integrated Products)IC DAC 16BIT SGL 16-TQFN PDF資料下載
參數資料
| 型號： | MAX5138BGTE+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/17頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SGL 16-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 設置時間： | 5µs |
| 位數： | 16 |
| 數據接口： | DSP，I²C，MICROWIRE?，并行，QSPI?，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN（3x3） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | * |
| 產品目錄頁面： | 1397 (CN2011-ZH PDF) |
Daisy chain multiple MAX5138/MAX5139 devices by
connecting the first device conventionally, then connect
its READY output to the CS of the following device.
Repeat for any other devices in the chain, and drive the
SCLK and DIN lines in parallel (Figure 5). When sending
commands to daisy-chained MAX5138/MAX5139s, the
devices are accessed serially starting with the first
device in the chain. The first 24 data bits are read by the
first device, the second 24 data bits are read by the sec-
ond device and so on (Figure 4). Figure 6 shows the
configuration when CS is not driven by the C. These
devices can be daisy chained with other compatible
devices, such as the MAX5510 and the MAX5511.
To perform a daisy-chain write operation, drive CS low
and output the data serially to DIN. The propagation of
the READY signal then controls how the data is read by
each device. As the data propagates through the daisy
chain, each individual command in the chain is execut-
ed on the 24th falling clock edge following the falling
edge of the respective CS input. To update just one
device in a daisy chain, send the no-op command to
the other devices in the chain.
If READY is not required, write command 0x03 (power
control) and set READY_EN = 0 (see Table 1) to dis-
able the READY output.
Clear Command
The MAX5138/MAX5139 feature a software clear com-
mand (0x02). The software clear command acts as a
software POR, erasing the contents of all registers. The
output returns to the state determined by the M/Z input.
Power-Down Mode
The MAX5138/MAX5139 feature a software-controlled
power-down mode. The internal reference and biasing
circuits power down to conserve power when powered
down. In power-down, the output disconnects from the
buffer and is grounded with an internal 80k
Ω resistor.
The DAC register holds the retained code so that the
output is restored when powered up. The serial inter-
face remains active in power-down mode.
Load DAC (LDAC) Input
The MAX5138/MAX5139 feature an active-low LDAC
logic input that updates the output. Keep LDAC high
during normal operation (when the device is controlled
only through the serial interface). Drive LDAC low to
update the DAC output with data from the input register.
Figure 7 shows the LDAC timing with respect to OUT.
Holding LDAC low causes the input register to become
transparent and data written to the DAC register to
immediately update the DAC output. A software com-
mand can also activate the LDAC operation. To activate
LDAC by software, set control word 0x01 to load the
DAC, and all other data bits to don’t care. See Table 1
for the data format. This operation updates the DAC out-
put if it is flagged with a 1. If the DAC output is flagged
with a 0 it remains unchanged.
Low-Power, Single, 16-/12-Bit,
Buffered Voltage-Output DACs
12
Maxim Integrated
MAX5138/MAX5139
μC
SLAVE 1
SCLK
DIN
CS
READY
MOSI
I/O
SCK
SLAVE 3
SCLK
DIN
CS
READY
SLAVE 2
SCLK
DIN
CS
READY
Figure 5. Daisy-Chain Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| VI-20H-MY-F3 | CONVERTER MOD DC/DC 52V 50W |
| VI-B6D-MV-F2 | CONVERTER MOD DC/DC 85V 150W |
| VI-20F-MY-F2 | CONVERTER MOD DC/DC 72V 50W |
| NB7V32MMNTXG | IC CLOCK DIVIDER 1.8/2.5V 16-QFN |
| MC100LVEL40DWR2G | IC DETECT PHASE-FREQ ECL 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5138BGTE+ | 功能描述:數模轉換器- DAC 16-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5138BGTE+T | 功能描述:數模轉換器- DAC 16-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5138EVKIT+ | 功能描述:數據轉換 IC 開發工具 MAX5138/39 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX5139 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Power, Single, 16-/12-Bit, Buffered Voltage-Output DACs |
| MAX5139GTE+ | 功能描述:數模轉換器- DAC 12-Bit Precision DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。