- 您現在的位置：買賣IC網 > PDF目錄1941 > MAX459CQH-D (Maxim Integrated Products)IC VIDEO CROSSPOINT SWIT 44PLCC PDF資料下載
參數資料
| 型號： | MAX459CQH-D |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/17頁 |
| 文件大小： | 0K |
| 描述： | IC VIDEO CROSSPOINT SWIT 44PLCC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 28 |
| 功能： | 視頻交叉點開關 |
| 電路： | 1 x 8:4 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
MAX458/MAX459
8x4 Video Crosspoint Switches with Buffers
______________________________________________________________________________________
13
__________Applications Information
Grounding and Bypassing,
PC Board Layout
As with all analog circuits, good PC board layout, prop-
er grounding, and careful component selection are cru-
cial for realizing the full AC performance of high-speed
amplifiers such as the MAX458/MAX459. For optimal
performance:
1) Use a large, low-impedance analog ground plane.
With multilayer boards, the ground plane(s) should
be located on the layer that does not contain signal
traces. Connect all GND pins to the analog ground
plane.
2) Minimize trace area at the circuit’s critical high-imped-
ance nodes to prevent unwanted signal coupling.
Surround analog inputs with an AC ground trace
(bypassed DC power supply, etc.). The analog input
pins of the MAX458/MAX459 have been separated
with AC ground pins (GND, VCC, VEE) to minimize
parasitic coupling, which can degrade crosstalk.
3) Connect the coaxial-cable shield to the ground side
of the 75
terminating resistor at the ground plane
to further reduce crosstalk (Figure 11).
4) Bypass all power-supply pins directly to the ground
plane with 0.1F ceramic capacitors placed as
close to the supply pins as possible. For high-cur-
rent loads, you may need 10F tantalum or alu-
minum-electrolytic capacitors in parallel with the
0.1F ceramics. Keep capacitor lead lengths as
short as possible to minimize series inductance; sur-
face-mount chip capacitors are ideal.
Creating Larger Arrays
The MAX458/MAX459 assume a high-impedance state
on power-up if the inputs are not being programmed to
any particular state during that time. They also are in a
high-impedance state when disabled. This feature
makes it possible to create larger arrays than 8x4 with-
out special programming, other than ensuring that your
program doesn’t turn on two paralleled outputs simulta-
neously. Testing has shown no degradation of differen-
tial gain or phase when the outputs are connected in
parallel.
The MAX458/MAX459’s input registers remain active dur-
ing shutdown, which allows the crosspoint to be pro-
grammed while the devices are shut down. As a result, all
outputs may be simultaneously brought to any state,
including disabled. Just program all of the MAX458/
MAX459s into shutdown, and enter the program of your
choice by selecting the desired inputs and outputs. Taking
SHDN low takes the device(s) out of shutdown.
A power-on reset circuit causes the output amplifiers to
power up in the disabled mode, whether or not SHDN
is applied, if
–
U
—
P
—
D
—
A
—
T
—
E
–
and
–
C
—
S
–
are high.
The number of MAX458s that can be paralleled is limit-
ed by capacitive loading on each output, which must
not exceed 100pF. Each input presents approximately
7pF of load, and each output presents approximately
12pF. Therefore, the MAX458/MAX459 will drive a maxi-
mum of 14 inputs, or 7 outputs and 2 inputs, or any
other combination resulting in less than a 100pF load.
Adding isolation resistors enables more MAX458s to be
paralleled (see the Driving Capacitive Loads section).
MAX458
MAX459
CS
SCLK
DIN
DOUT
SCK
MOSI
I/O
MOSO
THE DOUT-MOSO CONNECTION IS NOT REQUIRED FOR
WRITING TO THE MAX458/MAX459, BUT MAY BE USED
FOR DATA-ECHO PURPOSES.
CPOL = 0, CPHA = 0
SPI/QSPI
PORT
Figure 10. SPI/QSPI Connection
RETURN
CURRENT
IN_
RETURN
CURRENT
GROUND
PLANE
Figure 11. Low-Crosstalk Layout. Return current from termina-
tion resistor does not flow through the ground plane.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4603EAE | IC SWITCH QUAD SPST 16SSOP |
| MAX4604CPE | IC SWITCH QUAD SPST 16DIP |
| MAX4609CPE | IC SWITCH DUAL SPST 16DIP |
| MAX4612CSD | IC SWITCH QUAD SPST 14SOIC |
| MAX4613CUE | IC SWITCH QUAD SPST 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX459CQH-DW | 功能描述:模擬和數字交叉點 IC RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| MAX459CQH-DW-T | 功能描述:模擬和數字交叉點 IC RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| MAX459CQH-TD | 功能描述:視頻開關 IC RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX459EPL | 功能描述:視頻開關 IC RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX459EVKIT-PLC | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。