參數資料
型號: MAX44251EVKIT#
廠商: Maxim Integrated Products
文件頁數: 2/14頁
文件大?。?/td> 0K
描述: EVAL KIT OPAMP AUTOZERO MAX44251
產品培訓模塊: Obsolescence Mitigation Program
標準包裝: 1
每 IC 通道數: 2 - 雙
放大器類型: 自動調零
輸出類型: 滿擺幅
轉換速率: 8 V/µs
電流 - 輸出 / 通道: 96mA
工作溫度: -40°C ~ 125°C
電流供應(主 IC): 1.15mA
電壓 - 電源,單路/雙路(±): 2.7 V ~ 20 V,±1.35 V ~ 10 V
板類型: 完全填充
已供物品:
已用 IC / 零件: MAX44251
10
Maxim Integrated
MAX44250/MAX44251/MAX44252
20V, Ultra-Precision, Low-Noise Op Amps
Detailed Description
The MAX44250/MAX44251/MAX44252 are high-preci-
sion amplifiers that have less than 3FV of typical input-
referred offset and low flicker noise. These characteris-
tics are achieved through an autozeroing technique that
samples and finds repeating patterns of signal to cancel
the input offset voltage and 1/f noise of the amplifier.
Autozero
The ICs feature an autozero circuit that allows the devices
to achieve less than 6FV (max) of input offset voltage at
room temperature and eliminate the 1/f noise.
Noise Suppression
Flicker noise, inherent in all active devices, is inversely
proportional to frequency presented. Charges at the
oxide-silicon interface that are trapped-and-released by
MOSFET oxide occurs at low frequency more often. For
this reason, flicker noise is also called 1/f noise.
Electromagnetic interference (EMI) noise occurs at high-
er frequency that results in malfunction or degradation of
electrical equipment.
The ICs have an input EMI filter to avoid the output get-
ting affected by radio frequency interference. The EMI
filter composed of passive devices presents significant
higher impedance to higher frequency.
High Supply Voltage Range
The ICs feature 1.15mA current consumption per channel
and a voltage supply range from either 2.7V to 20V single
supply or ±1.35V to ±10V split supply.
Applications Information
The ICs are ultra-high-precision operational amplifiers with
a high supply voltage range designed for load cell, medi-
cal instrumentation and precision instrument applications.
These devices are also designed to interface with pres-
sure transducers and are ideal for precision weight scale
application as shown in Figure 1.
Figure 1. Weight Scale Application Circuit
10V
+10V
3.3V
3V
VDD
MICRO-
PROCESSOR
VOUT
50RG
RG
VREF
VDD
VSS
VIN-
VIN+
C1
BUFFER
MAX44251
MAX11211
MAX6126
MAX44251
R
+10V
1.5V
BUFFER
R
R1
OUTPUT
-10V
相關PDF資料
PDF描述
222D221-4-61/42-0 BOOT MOLDED
FFSD-09-S-04.00-01-N CABLE ASSEMBLY FLAT 0.101M 30AWG
MIC2004-1.2YM5TX IC DISTRIBUTION SW 1.2A SOT23-5
GSC06DRYS-S93 CONN EDGECARD 12POS DIP .100 SLD
202K153-100-01/180-0 BOOT MOLDED
相關代理商/技術參數
參數描述
MAX44251EVKIT# 功能描述:放大器 IC 開發工具 MAX44251 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX44251EVKIT+ 功能描述:放大器 IC 開發工具 20V ultra-precision low-noise low-drift amplifiers RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX44252ASD+ 功能描述:運算放大器 - 運放 20V Ultra-Precision Low-Noise Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MAX44252ASD+T 功能描述:運算放大器 - 運放 20V Ultra-Precision Low-Noise Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MAX44252EVKIT# 功能描述:放大器 IC 開發工具 20V Ultra-Precision Low-Noise Op Amp RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V