- 您現在的位置：買賣IC網 > PDF目錄10443 > MAX4409ETP+ (Maxim Integrated Products)IC AMP AUDIO .08W STER AB 20TQFN PDF資料下載
參數資料
| 型號： | MAX4409ETP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/20頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO .08W STER AB 20TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 75 |
| 系列： | DirectDrive® |
| 類型： | AB 類 |
| 輸出類型： | 耳機，2-通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 80mW x 2 @ 16 歐姆 |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 特點： | 消除爆音，短路保護和熱保護，關閉 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 20-TQFN-EP（4x4） |
| 封裝/外殼： | 20-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
| 產品目錄頁面： | 1390 (CN2011-ZH PDF) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
MAX4409
80mW, DirectDrive, Stereo Headphone
Amplifier with Common-Mode Sense
10
______________________________________________________________________________________
typically 0.5mV, which, when combined with a 32
Ω
load, results in less than 16A of DC current flow to the
headphones.
Previous attempts to eliminate the output-coupling capac-
itors involved biasing the headphone return (sleeve) to
the DC-bias voltage of the headphone amplifiers. This
method raises some issues:
When combining a microphone and headphone on
a single connector, the microphone bias scheme
typically requires a 0V reference.
The sleeve is typically grounded to the chassis.
Using this biasing approach, the sleeve must be
isolated from system ground, complicating product
design.
During an ESD strike, the driver’s ESD structures
are the only path to system ground. Thus, the driver
must be able to withstand the full ESD strike.
When using the headphone jack as a line out to other
equipment, the bias voltage on the sleeve may con-
flict with the ground potential from other equipment,
resulting in possible damage to the drivers.
Low-Frequency Response
In addition to the cost and size disadvantages of the DC-
blocking capacitors required by conventional head-
phone amplifiers, these capacitors limit the amplifier’s
low-frequency response and can distort the audio signal:
The impedance of the headphone load and the DC-
blocking capacitor form a highpass filter with the
-3dB point set by:
where RL is the headphone impedance and COUT is
the DC-blocking capacitor value. The highpass filter
is required by conventional single-ended, single
power-supply headphone drivers to block the midrail
DC bias component of the audio signal from the
headphones. The drawback to the filter is that it can
attenuate low-frequency signals. Larger values of
COUT reduce this effect but result in physically larg-
er, more expensive capacitors. Figure 2 shows the
relationship between the size of COUT and the result-
ing low-frequency attenuation. Note that the -3dB
point for a 16
Ω headphone with a 100F blocking
capacitor is 100Hz, well within the normal audio
band, resulting in low-frequency attenuation of the
reproduced signal.
The voltage coefficient of the DC-blocking capacitor
contributes distortion to the reproduced audio signal
as the capacitance value varies as a function of the
voltage change across the capacitor. At low fre-
quencies, the reactance of the capacitor dominates
at frequencies below the -3dB point and the voltage
coefficient appears as frequency-dependent distor-
tion. Figure 3 shows the THD+N introduced by two
different capacitor dielectric types. Note that below
100Hz, THD+N increases rapidly.
The combination of low-frequency attenuation and fre-
quency-dependent distortion compromises audio
reproduction in portable audio equipment that empha-
sizes low-frequency effects such as multimedia lap-
f
RC
dB
L OUT
-
2
3
1
=
π
LF ROLL OFF (16
Ω LOAD)
MAX4409
fig02
FREQUENCY (Hz)
ATTENUATION
(dB)
100
-30
-25
-20
-10
-3dB CORNER FOR
100
μF IS 100Hz
-15
-5
-3
0
-35
10
1k
33
μF
330
μF
220
μF
100
μF
Figure 2. Low-Frequency Attenuation for Common DC-Blocking
Capacitor Values
ADDITIONAL THD+N DUE
TO DC-BLOCKING CAPACITORS
MAX4409
fig03
FREQUENCY (Hz)
THD+N
(%)
10k
1k
100
0.001
0.01
0.1
1
10
0.0001
10
100k
TANTALUM
ALUM/ELEC
Figure 3. Distortion Contributed by DC-Blocking Capacitors
相關PDF資料 |
PDF描述 |
|---|---|
| VI-271-IW-F2 | CONVERTER MOD DC/DC 12V 100W |
| VE-JNN-MY-B1 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-B74-MX-F2 | CONVERTER MOD DC/DC 48V 75W |
| VE-JNM-MY-B1 | CONVERTER MOD DC/DC 10V 50W |
| VI-26X-IW-F1 | CONVERTER MOD DC/DC 5.2V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4409ETP+ | 功能描述:音頻放大器 80mW DirectDrive Stereo Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX4409ETP+T | 功能描述:音頻放大器 80mW DirectDrive Stereo Headphone Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX4409ETP-T | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX4409EUD | 制造商:Maxim Integrated Products 功能描述:80MW, DIRECTDRIVE, STEREO HEADPHONE AMPLIFIER - Bulk |
| MAX4409EUD+ | 制造商:Maxim Integrated Products 功能描述:AUD AMP HDPH 2CH STEREO 0.08W CLS-AB 14TSSOP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。