- 您現在的位置：買賣IC網 > PDF目錄16898 > MAX4206EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX4206 PDF資料下載
參數資料
| 型號： | MAX4206EVKIT |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL KIT FOR MAX4206 |
| 標準包裝： | 1 |
| 每 IC 通道數： | 1 - 單 |
| 放大器類型： | 對數 |
| 輸出類型： | 單端 |
| 轉換速率： | 12 V/µs |
| 電流 - 輸出 / 通道： | 58mA |
| 工作溫度： | 0°C ~ 70°C |
| 電流供應（主 IC）： | 5mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 11 V，±2.7 V ~ 5.5 V |
| 板類型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX4206，MAX4207 |
MAX4206
Precision Transimpedance Logarithmic
Amplifier with Over 5 Decades of Dynamic Range
______________________________________________________________________________________
13
Frequency Response and Noise Considerations
The MAX4206 bandwidth is proportional to the magni-
tude of the IREF and ILOG currents, whereas the noise is
inversely proportional to IREF and ILOG currents.
Common Mode
A common-mode input voltage, VCMVOUT, of 0.5V is
available at CMVOUT and can be used to bias the log-
ging and reference amplifier inputs by connecting
CMVOUT to CMVIN. An external voltage between 0.5V
and 1V can be applied to CMVIN to bias the logging
and reference transistor collectors and to optimize the
performance required for both single- and dual-supply
operation.
Adjusting the Logarithmic Intercept
Adjust the logarithmic intercept by changing the refer-
ence current, IREF. A resistor from REFISET to GND
(see Figures 5 and 6) adjusts the reference current,
according to the following equation:
where VREFISET is 0.5V. Select RSET between 5k and
5M. REFIOUT current range is 10nA to 10A only.
Single-Supply Operation
When operating from a single +2.7V to +11V supply,
ILOG must be greater than IREF, resulting in a positive
slope of the log output voltages, LOGV1 and LOGV2.
Bias the log and reference amplifiers by connecting
CMVOUT to CMVIN or connecting an external voltage
reference between 0.5V and 1V to CMVIN. For single-
supply operation, connect VEE to GND.
Output Offset
Select ROS and IOS to adjust the output offset voltage
(see Figure 5). The magnitude of the offset voltage is
given by:
VOS = ROS IOSADJ
Scale Factor
The scale factor, K, is the slope of the logarithmic out-
put. For the LOGV1 amplifier, K = 0.25V/decade. When
operating in a single-supply configuration, adjust the
overall scale factor for the MAX4206 using the uncom-
mitted LOGV2 amplifier and the following equation,
which refers to Figure 5:
Select R1 between 1k and 100k, with an ideal value
of 10k. The noninverting amplifier ensures that the
overall scale factor is greater than or equal to
0.25V/decade for single-supply operation.
Design Example
Desired:
Single-Supply Operation
Logarithmic intercept: 100nA
Overall scale factor = 1V/decade
Because there is no offset current applied to the circuit
(ROS = 0), the reference current, IREF, equals the log
intercept of 100A. Therefore,
Select R1 = 10k:
Dual-Supply Operation
When operating from dual ±2.7 to ±5.5V supplies, it is
not required that ILOG be greater than IREF. A positive
output voltage results at LOGV1 when ILOG exceeds
IREF. A negative output voltage results at LOGV1 when
ILOG is less than IREF. Bias the log and reference
amplifiers by connecting CMVOUT to CMVIN or con-
nect an external 0.5V to 1V reference to CMVIN. For
dual-supply operation with CMVIN < 0.5V, refer to the
MAX4207 data sheet.
Output Offset
The uncommitted amplifier in the inverting configuration
utilized by the MAX4206 facilitates large output-offset
voltage adjustments when operated with dual supplies.
The magnitude of the offset voltage is given by the fol-
lowing equation:
A resistive divider between REFVOUT, OSADJ, and
GND can be used to adjust VOSADJ (see Figure 6).
VV
R
RR
OSADJ
REFOUT
=
+
4
34
VV
R
OS
OSADJ
=+
1
2
1
Rk
VV
k
210
1
025
130
=
=
/
.
R
V
nA
k
SET =
×
=
05
10 100
500
.
RR
K
21
025
1
=
.
R
V
I
SET
REFISET
REF
=
×
10
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2566-1BM TR | IC PCMCIA/CARDBUS SGL 14-SOP |
| EBM15DCCT-S189 | CONN EDGECARD 30POS R/A .156 SLD |
| RBC07DRAH-S734 | CONN EDGECARD 14POS .100 R/A PCB |
| LM4050CEX3-2.1+T | IC VREF SHUNT PREC 2.048V SC70-3 |
| 202A174-4/86-0 | BOOT MOLDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4206EVKIT+ | 功能描述:放大器 IC 開發工具 MAX4206 EVAL KIT RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX4207ETE | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4207ETE+ | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4207ETE+T | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX4207ETE-T | 功能描述:對數放大器 Transimpedance w/ 100Db Dynamic Range RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。