- 您現在的位置：買賣IC網 > PDF目錄385528 > MAX4091-MAX4094 (Maxim Integrated Products, Inc.) Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps PDF資料下載
參數資料
| 型號： | MAX4091-MAX4094 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps |
| 中文描述： | 單/雙/四路，微功耗，單電源，軌至軌運算放大器 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 514K |
| 代理商： | MAX4091-MAX4094 |
M
Single/Dual/Quad, Micropower, Single-Supply,
Rail-to-Rail Op Amps
_______________________________________________________________________________________
9
tance. If the output sources either more or less current,
stability is increased. These devices perform well with a
1000pF pure capacitive load (Figure 5). Figures 6a, 6b,
and 6c show the performance with a 500pF load in par-
allel with various load resistors.
To increase stability while driving large-capacitive
loads, connect a pullup resistor to V
CC
at the output to
decrease the current the amplifier must source. If the
amplifier is made to sink current rather than source,
stability is further increased.
Frequency stability can be improved by adding an out-
put isolation resistor (R
S
) to the voltage-follower circuit
(Figure 7). This resistor improves the phase margin of
the circuit by isolating the load capacitor from the op
amp
’
s output. Figure 8a shows the MAX4092 driving
5000pF (R
L
≥
100k
), while Figure 8b adds a 47
iso-
lation resistor.
Because the MAX4091/MAX4092/MAX4094 have excel-
lent stability, no isolation resistor is required, except in
the most demanding applications. This is beneficial
because an isolation resistor would degrade the low-
frequency performance of the circuit.
Power-Up Settling Time
The MAX4091/MAX4092/MAX4094 have a typical sup-
ply current of 130μA per op amp. Although supply cur-
rent is already low, it is sometimes desirable to reduce
it further by powering down the op amp and associated
ICs for periods of time. For example, when using a
MAX4092 to buffer the inputs of a multi-channel analog-
to-digital converter (ADC), much of the circuitry could
be powered down between data samples to increase
battery life. If samples are taken infrequently, the op
amps, along with the ADC, may be powered down
most of the time.
When power is reapplied to the MAX4091/MAX4092/
MAX4094, it takes some time for the voltages on the
supply pin and the output pin of the op amp to settle.
Supply settling time depends on the supply voltage, the
value of the bypass capacitor, the output impedance of
the incoming supply, and any lead resistance or induc-
tance between components. Op amp settling time
depends primarily on the output voltage and is slew-
rate limited. With the noninverting input to a voltage fol-
lower held at midsupply (Figure 9), when the supply
steps from 0 to V
CC
, the output settles in approximately
2μs for V
CC
= 3V (Figure 10a) and 8μs for V
CC
= 5V
(Figure 10b).
Power Supplies and Layout
The MAX4091/MAX4092/MAX4094 operate from a sin-
gle 2.7V to 6V power supply, or from dual supplies of
±1.35V to ±3V. For single-supply operation, bypass the
power supply with a 0.1μF capacitor. If operating from
dual supplies, bypass each supply to ground.
Good layout improves performance by decreasing the
amount of stray capacitance at the op amp
’
s inputs
and output. To decrease stray capacitance, minimize
both trace lengths and resistor leads and place exter-
nal components close to the op amp
’
s pins.
Chip Information
MAX4091 TRANSISTOR COUNT: 168
MAX4092 TRANSISTOR COUNT: 336
MAX4094 TRANSISTOR COUNT: 670
PROCESS: Bipolar
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4094 | Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps |
| MAX4102 | 250MHz, Broadcast-Quality, Low-Power Video Op Amps |
| MAX4102ESA | 250MHz, Broadcast-Quality, Low-Power Video Op Amps |
| MAX4103ESA | 250MHz, Broadcast-Quality, Low-Power Video Op Amps |
| MAX4105 | 740MHz, Low-Noise, Low-Distortion Op Amps in SOT23-(740MHz,Avcl=+1,低噪,SOT23雙電源/射頻運放) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4092 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Quad.Micropower.Single-Supply.Rail-to-Rail Op Amps |
| MAX4092ASA | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4092ASA+ | 功能描述:運算放大器 - 運放 Dual uPower Single Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4092ASA+T | 功能描述:運算放大器 - 運放 Dual uPower Single Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX4092ASA-T | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。