- 您現在的位置：買賣IC網 > PDF目錄385528 > MAX4090 (Maxim Integrated Products, Inc.) 3V/5V, 6dB Video Buffer with Sync-Tip Clamp and 150nA Shutdown Current PDF資料下載
參數資料
| 型號： | MAX4090 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 3V/5V, 6dB Video Buffer with Sync-Tip Clamp and 150nA Shutdown Current |
| 中文描述： | 3V/5V、6dB視頻緩沖器，具有同步頭鉗位和150nA關斷電流 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 651K |
| 代理商： | MAX4090 |
M
3V/5V, 6dB Video Buffer with Sync-Tip Clamp
and 150nA Shutdown Current
_______________________________________________________________________________________
7
Detailed Description
The MAX4090 3V/5V, 6dB video buffer with sync-tip
clamp and low-power shutdown mode is available in tiny
SOT23 and SC70 packages. The MAX4090 is designed
to drive DC-coupled, 150
back-terminated video loads
in portable video applications such as digital still cams,
portable DVD players, digital camcorders, PDAs, video-
enabled cell phones, portable game systems, and note-
book computers. The input clamp positions the video
waveform at the output and allows the MAX4090 to be
used as a DC-coupled output driver.
The MAX4090 operates from a single 2.7V to 5.5V sup-
ply and consumes only 6.5mA of supply current. The
low-power shutdown mode reduces the supply current
to 150nA, making the MAX4090 ideal for low-voltage,
battery-powered video applications.
The input signal to the MAX4090 is AC-coupled
through a capacitor into an active sync-tip clamp cir-
cuit, which places the minimum of the video signal at
approximately 0.38V. The output buffer amplifies the
video signal while still maintaining the 0.38V clamp volt-
age at the output. For example, if V
IN
= 0.38V, then
V
OUT
= 0.38V. If V
IN
= (0.38V + 1V) = 1.38V, then V
OUT
= (0.38V + 2 X (1V)) = 2.38V. The net result is that a 2V
video output signal swings within the usable output
voltage range of the output buffer when V
CC
= 3V.
Shutdown Mode
The MAX4090 features a low-power shutdown mode
(I
SHDN
= 150nA) for battery-powered/portable applica-
tions. Pulling the
SHDN
pin high enables the output.
Connecting the
SHDN
pin to ground (GND) disables
the output and places the MAX4090 into a low-power
shutdown mode.
Applications Information
Input Coupling the MAX4090
The MAX4090 input must be AC-coupled because the
input capacitor stores the clamp voltage. The MAX4090
requires a typical value of 0.1μF for the input clamp to
meet the Line Droop specification. A minimum of a
ceramic capacitor with an X7R temperature coefficient
is recommended to avoid temperature-related prob-
lems with Line Droop. For extended temperature opera-
tion, such as outdoor applications, or where the
impressed voltage is close to the rated voltage of the
capacitor, a film dielectric is recommended. Increasing
the capacitor value slows the clamp capture time.
Values above 0.5μF should be avoided since they do
not improve the clamp’s performance.
The active sync-tip clamp also requires that the input
impedance seen by the input capacitor be less than
100
typically to function properly. This is easily met
by the 75
input resistor prior to the input-coupling
capacitor and the back termination from a prior stage.
Insufficient input resistance to ground causes the
MAX4090 to appear to oscillate. Never operate the
MAX4090 in this mode.
Using the MAX4090 with the
Reconstruction Filter
In most video applications, the video signal generated
from the DAC requires a reconstruction filter to smooth
out the signal and attenuate the sampling aliases. The
MAX4090 is a direct DC-coupled output driver, which
can be used after the reconstruction filter to drive the
video signal. The driving load from the video DAC can
be varied from 75
to 300
. A low input impedance
(<100
) is required by the MAX4090 in normal opera-
tion, special care must be taken when a reconstruction
filter is used in front of the MAX4090.
For standard video signal, the video passband is about
6MHz and the system oversampling frequency is at
27MHz. Normally, a 9MHz BW lowpass filter can be
used for the reconstruction filter. This section demon-
strates the methods to build simple 2nd- and 3rd-order
passive butterworth lowpass filters at the 9MHz cutoff
frequency and the techniques to use them with the
MAX4090 (Figures 1 and 4).
2nd-Order Butterworth Lowpass Filter Realization
Table 1 shows the normalized 2nd-order butterworth
LPF component values at 1rad/s with a source/load
impedance of 1
.
With the following equations, the L and C can be calcu-
lated for the cutoff frequency at 9MHz. Table 2 shows
the appropriated L and C values for different source/
load impedance, the bench measurement values for
the -3dB BW and attenuation at 27MHz. There is
approximately 20dB attenuation at 27MHz, which effec-
tively attenuates the sampling aliases. The MAX4090
requires low input impedance for stable operation and
it does not like the reactive input impedance. For R1/R2
greater than 100
, a series resistor R
IS
(Figure 1)
R
n
1 = R
n
2 (
)
1
C
n
1 (F)
1.414
L
n
1 (H)
1.414
Table 1. 2nd Order Butterworth Lowpass
Filter Normalized Values
相關PDF資料 |
PDF描述 |
|---|---|
| MAX4090EUT-T | 3V/5V, 6dB Video Buffer with Sync-Tip Clamp and 150nA Shutdown Current |
| MAX4090EXT-T | 3V/5V, 6dB Video Buffer with Sync-Tip Clamp and 150nA Shutdown Current |
| MAX4091 | Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps |
| MAX4091ASA | Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps |
| MAX4091AUA | Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX4090_05 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3V/5V, 6dB Video Buffer with Sync-Tip Clamp and 150nA Shutdown Current |
| MAX4090_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3V/5V, 6dB Video Buffer with Sync-Tip Clamp and 150nA Shutdown Current |
| MAX4090AALT | 制造商:Maxim Integrated Products 功能描述:3V/5V 6DB VIDEO BUFFER WITH SYNC-T - Rail/Tube |
| MAX4090AALT+ | 制造商:Maxim Integrated Products 功能描述:VID BFFR 6PIN UDFN - Rail/Tube |
| MAX4090AALT+T | 功能描述:視頻放大器 3V/5V 6dB Video Buff w/Sync-Tip Clamp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。