
M
3.0V to 5.5V, 2.5Gbps VCSEL
and Laser Driver
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Supply Voltage at V
CC
...........................................-0.5V to +7.0V
Voltage at TX_DISABLE, PORDLY, MON1, COMP,
IN+, IN-, MD, BIAS, MODSET, TC..........-0.5V to (V
CC
+ 0.5V)
Voltage between COMP and MON2.....................................2.3V
Voltage between IN+ and IN- ..................................................5V
Voltage at OUT+, OUT-.........................(V
CC
- 2V) to (V
CC
+ 2V)
Voltage between MON1 and MON2 .....................................1.5V
Voltage between BIAS and MON2...........................................4V
ELECTRICAL CHARACTERISTICS
(V
CC
= 3.0V to 5.5V, T
A
= 0°C to +70°C, unless otherwise noted. Typical values are at V
CC
= 3.3V, TC pin not connected, T
A
=
+25°C.) (Figure 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Current into FAULT, SHDNDRV..........................-1mA to +25mA
Current into OUT+, OUT-....................................................60mA
Current into BIAS ..............................................................120mA
Continuous Power Dissipation (T
A
= +70°C)
20-Pin QFN (derate 20mW/°C)...................................1600mW
Operating Ambient Temperature Range.............-40°C to +85°C
Operating Junction Temperature Range...........-40°C to +150°C
Storage Temperature Range.............................-55°C to +150°C
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
47
MAX
UNITS
V
CC
= 3.3V, I
MOD
= 15mA
V
CC
= 5.5V, I
MOD
= 30mA,
R
MODSET
= 2.37k
Total differential signal (Figure 2)
0 < V
PIN
< V
CC
Supply Current
I
CC
(Figure1)
(Note 1)
52
75
mA
Data Input Voltage Swing
TX_DISABLE Input Current
TX_DISABLE Input High Voltage
TX_DISABLE Input Low Voltage
FAULT Output High Voltage
FAULT Output Low Voltage
BIAS GENERATOR
Minimum Bias Current
Maximum Bias Current
V
ID
200
-100
2.0
2200
100
MV
P-P
μA
V
V
V
V
V
IH
V
IL
V
OH
V
OL
0.8
I
OH
= -100μA, 4.7k
< R
FAULT
< 10k
I
OL
= 1mA
2.4
0.4
I
BIAS
I
BIAS
Current into BIAS pin
Current into BIAS pin
APC loop is closed
FAULT = high
TX_DISABLE = high
(Figure 4)
FAULT = low, TX_DISABLE = low
1
mA
mA
60
1.04
1.12
V
CC
- 0.73
V
CC
- 0.73
11
0.8
MD Quiescent Voltage
V
MD
V
Monitor Resistance
MD Input Current
BIAS Current During Fault
APC Time Constant
POWER-ON RESET (POR)
POR Threshold
R
MON
9.3
-3
12.7
3
10
μA
μA
μs
I
BIAS_OFF
C
COMP
= 0.1μF
35
Measured at V
CC
PORDLY = open (Note 3)
C
PORDLY
= 0.001μF (Note 3)
2.65
30
1.7
2.7
55
2.4
20
3.0
V
μs
ms
mV
POR Delay
t
PORDLY
POR Hysteresis
SHUTDOWN
I
SHDNDRV
= 10μA, FAULT = high
I
SHDNDRV
= 1mA, FAULT = low
I
SHDNDRV
= 15mA, FAULT = low
V
CC
- 0.4
V
CC
- 2.4
V
CC
- 1.2
Voltage at SHDNDRV
0
V
LASER MODULATOR
Data Rate
< 3.2
Gbps