參數資料
型號: MAX385MJE
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 運動控制電子
英文描述: Dual LVDS Transmitter/Receiver 16-TSSOP -40 to 85
中文描述: DUAL 2-CHANNEL, DBL POLE SGL THROW SWITCH, CDIP16
封裝: CERDIP-16
文件頁數: 8/12頁
文件大小: 125K
代理商: MAX385MJE
M
Prec ision, Low-Voltage Analog S witc hes
8
_______________________________________________________________________________________
__________Applic ations Information
Operation with S upply V oltages
Other than ±5V
The MAX381/MAX383/MAX385 switches operate with
±3.0V to ±8V bipolar supplies and a +3V to +15V single
supply. In either case, analog signals ranging from V+ to
V- can be switched. The Typical Operating Characteristics
graphs show the typical on-resistance variation with ana-
log signal and supply voltage. The usual on-resistance
temperature coefficient is 0.5%/°C (typ).
Overvoltage Protec tion
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, NO, or COM. If power-supply sequencing
is not possible, add two small signal diodes (D1, D2) in
series with supply pins for overvoltage protection
(Figure 1). Adding diodes reduces the analog signal
range to one diode drop below V+ and one diode drop
above V-, but does not affect the devices’ low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between
V+ and V- should not exceed 17V. These protection
diodes are not recommended when using a single 3V
supply.
______________________________________________________________Pin Desc ription
COM
V-
V+
NO
* INTERNAL PROTECTION DIODES
D2
D1
-5V
+5V
MAX381
MAX383
MAX385
*
*
*
*
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
1, 8
COM_
Analog Switch Common Terminal
2–7, 12
N.C.
Not Internally Connected
9, 16
NO_
Analog Switch Normally Open Terminal
NC_
Analog Switch Normally Closed Terminal
10, 15
IN_*
Logic Level Input (Normally Low)
11
V+
Analog Signal and Logic Positive Supply Input
14
V-
Analog Signal Negative Supply Input
NAME
FUNCTION
MAX381
1, 3, 6, 8
2, 7, 12
9, 16
4, 5
10, 15
11
14
MAX383
1, 3, 6, 8
2, 7, 12
4, 5, 9, 16
10, 15
11
14
MAX385
PIN
13
GND
Logic Negative Supply Input (Ground)
13
13
* IN1 controls COM1 and COM3; IN2 controls COM2 and COM4.
相關PDF資料
PDF描述
MAX381_3_5
MAX381CPE Precision, Low-Voltage Analog Switches
MAX381CSE Precision, Low-Voltage Analog Switches
MAX381EPE Precision, Low-Voltage Analog Switches
MAX381ESE Precision, Low-Voltage Analog Switches
相關代理商/技術參數
參數描述
MAX3861E/D 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX3861EGG 功能描述:限幅放大器 2.7Gbps Post Amp w/Auto Gain Control RoHS:否 制造商:Micrel 輸入電壓范圍(最大值):3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube
MAX3861EGG-T 功能描述:限幅放大器 2.7Gbps Post Amp w/Auto Gain Control RoHS:否 制造商:Micrel 輸入電壓范圍(最大值):3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube
MAX3861ETG+ 功能描述:限幅放大器 2.7Gbps Post Amp w/Auto Gain Control RoHS:否 制造商:Micrel 輸入電壓范圍(最大值):3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube
MAX3861ETG+T 功能描述:限幅放大器 2.7Gbps Post Amp w/Auto Gain Control RoHS:否 制造商:Micrel 輸入電壓范圍(最大值):3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube