- 您現在的位置：買賣IC網 > PDF目錄2088 > MAX3816ACUE+T (Maxim Integrated Products)IC I2C 2WIRE EXTENDER 16-TSSOP PDF資料下載
參數資料
| 型號： | MAX3816ACUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I2C 2WIRE EXTENDER 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 擴展件 |
| 應用： | HD 顯示器，DVI/HDMI |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
MAX3816A
I2C 2-Wire Extender for DDC in DVI,
HDMI, and VGA Interfaces
_______________________________________________________________________________________
7
meter (> 3000pF) cable with a controlled slew-rate.
Similarly, the display side is pulled down to VSS with
a controlled slew rate, open-drain n-channel MOS
device. These buffers stay on for 1.75s.
3) Low state. Level sensing off (Holdoff).
Level sensing remains off until the completion of the
holdoff period, which is 2.5s on both the clock and
data channels.
In series mode, drivers maintain low level (at or
below VHOLD). Either the client pulldowns sustain
the level below VOL, or the MAX3816A sustains the
level at VHOLD if no other driver on the same node
is pulling down. This action is in support of the
“wired-AND” function across source and display
sides.
4) Low state, drivers off. Level sensing on.
After the MAX3816A holdoff time completes, level
sensing resumes.
In series mode, the MAX3816A supports a “wired-
AND” connection between source and display
sides; returning to the high state is supported only
when all client sources turn off. If either the source
or display side releases the bus, but not both, a
MAX3816A level-sensing buffer senses the transi-
tion at VTRIGIL, supporting the existing low state by
clamping the voltage to VHOLD and waiting for the
remaining side to release the bus.
5) Low-to-high transition. Drivers on. Level sensing
off (Holdoff).
A change of state is initiated when no device is
holding the bus low on both source and display
sides. When both sides exceed their respective
VTRIGIL levels, the source side turns on a slew-rate
controlled open-drain p-channel device, pulling up
to VCC for 1.75s. Simultaneously, the display side
is released and the pullup resistors pull the display-
side bus up to VDD, as per normal I2C operation.
6) High state. Drivers off. Level sensing off
(Holdoff).
During holdoff, no transitions are sensed. The high
state is maintained by external pullup resistors. Upon
the end of holdoff, when the cable and display levels
are above 85%, the state machine transitions to state
(1); otherwise, it waits until levels raise above 85% to
transition to state (1). Data, but not clock, has anoth-
er exit from state (6) to (1) upon data source or data
display levels dropping below 60%.
I2C continuous clock applications are not recommend-
ed for the MAX3816A. The MAX3816A is optimized for
DDC applications with a noncontinuous clock.
Detailed Description
The MAX3816A DDC/I2C 2-wire extender consists of
two controllers with level-shifters, cable drivers, display
drivers, and level-sensing circuitry (Figure 2).
Controllers and Level Shifters
The MAX3816A functionality is governed by two con-
trollers, one for CLOCK and one for DATA. Bidirectional
signaling is fully supported on both CLOCK and DATA.
The primary function of the controllers is to receive the
state-change information from the source- and display-
side level-sense circuitry and support the “wired-AND”
function between the two. When the state changes, a
holdoff period is timed during which the source and
display drivers assert the next state, high or low, and all
input sensing is ignored while I/O transients settle
(Figure 3). The holdoff period is approximately 2.5s.
The cable transmission-line termination feature is active
only during the first 1.75s of holdoff, sufficiently long
enough to absorb roundtrip reflections from a 60m
cable.
In series mode, the CLOCK and DATA controllers iso-
late the source electronics from the display electronics.
The cable side of the MAX3816A is referenced to VCC
and GND_REF, and the display side is referenced to
VDD and VSS. This power scheme provides tolerance to
offset and noise between the source and display
devices.
Cable Drivers
The low-impedance cable drivers (Figure 10) can
charge and discharge at least 3000pF of capacitive
cable load within the I2C rise and fall time limits. The
drivers each incorporate a slew-rate limiter to control
the amount of high-frequency energy transmitted. The
cable drivers also provide a back termination imped-
ance of approximately 60
Ω to absorb transmission-line
reflections returning to the driver. The cable drivers
each include a high-state current-limiting feature to
clamp the output current to less than 16mA.
After 1.75s of driver assertion, following a decision to
transition, the low-impedance drivers are turned off.
Subsequently, when another device asserts a new
state, it does not have to work against the low imped-
ance of the MAX3816A.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3845UCQ+TD | IC SW/CBL DRVR DVI/HDMI 100TQFP |
| MAX384EPN | IC MUX 8CH DUAL 4CH LTCHBL 18DIP |
| MAX3861EGG | IC POST AMP 2.7GBPS W/AGC 24TQFN |
| MAX3945ETE+ | IC AMP LIMITING 3.3V LP 16TQFN |
| MAX3964AETP+T | IC AMP LIMITING SGNL DET 20-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3816CUE+ | 功能描述:I2C 接口集成電路 TMDS Digi Video EQ for HDMI/DVI Cables RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| MAX3816CUE+T | 功能描述:I2C 接口集成電路 TMDS Digi Video EQ for HDMI/DVI Cables RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| MAX381BCPE | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX381BCSE | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX381BCSE-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。