- 您現在的位置：買賣IC網 > PDF目錄383370 > MAX365CPE (MAXIM INTEGRATED PRODUCTS INC) Precision, Quad, SPST Analog Switches PDF資料下載
__________Applic ations Information
Applic ation Hints
1. Switches are open when power is off.
2. IN_, COM_, NO_, and NC_ should not exceed V+ or
V-, even with the power off.
3. Switch leakage is from each analog switch terminal
to V+ or V-, not to the other switch terminal.
Operation with S upply V oltages
Other than ±15V
O
The main limitation of supply voltages other than ±15V is
reduction in the analog signal range. The MAX364/MAX365
switches operate with ±5V to ±20V bipolar supplies. The
Typical Operating Characteristics graphs show typical on
resistance for ±15V, ±10V, and ±5V supplies. Switching
times increase by a factor of two or more for ±5V opera-
tion. The MAX364/MAX365 operate from unipolar sup-
plies of +10V to +24V. Both parts can be powered from a
single +10V to +24V supply, as well as from unbalanced
supplies, such as +24V and -5V. Connect V- to 0V when
operating with a single supply. VL must be connected to
+5V to be TTL compatible or to V+ for CMOS logic input
levels.
Overvoltage Protec tion
Proper power-supply sequencing is recommended for
all CMOS devices. It is important not to exceed the
absolute maximum ratings, because stresses beyond
those listed may cause permanent damage to the
devices. Always sequence V+ on first, followed by VL,
V-, and logic inputs. If power-supply sequencing is not
possible, protect the devices from overvoltage by
adding two small signal diodes in series with the supply
pins (Figure 1). Adding the diodes reduces the analog
signal range to 1V below V+ and 1V below V-, but low
switch resistance and low leakage characteristics are
unaffected. Device operation is unchanged, and the
difference between V+ to V- should not exceed +44V.
M
Prec ision, Quad, S PS T Analog S witc hes
_______________________________________________________________________________________
7
V+
COM_
V-
NO_
V
g
Figure 1. Overvoltage Protection Using Blocking Diodes
相關PDF資料 |
PDF描述 |
|---|---|
| MAX365CSE | Precision, Quad, SPST Analog Switches |
| MAX365EPE | Precision, Quad, SPST Analog Switches |
| MAX365ESE | Precision, Quad, SPST Analog Switches |
| MAX364CPE | Dual LVDS Transmitter/Receiver 16-SOIC -40 to 85 |
| MAX364CSE | Dual LVDS Transmitter/Receiver 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX365CPE+ | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX365CSE | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX365CSE+ | 功能描述:模擬開關 IC Precision Quad SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX365CSE+T | 功能描述:模擬開關 IC Precision Quad SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX365CSE-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。