- 您現在的位置：買賣IC網 > PDF目錄384665 > MAX3656ETG (MAXIM INTEGRATED PRODUCTS INC) 155Mbps to 2.5Gbps Burst-Mode Laser Driver PDF資料下載
參數資料
| 型號： | MAX3656ETG |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 其它接口 |
| 英文描述： | 155Mbps to 2.5Gbps Burst-Mode Laser Driver |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, QCC24 |
| 封裝： | 4 X 4 MM, TQFN-24 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 734K |
| 代理商： | MAX3656ETG |
M
155Mbps to 2.5Gbps Burst-Mode
Laser Driver
_______________________________________________________________________________________
7
TIMING DIAGRAM, BURST ON
500ps/div
V
MOD+
V
BIAS+
BURST-ENABLE
SIGNAL
TIMING DIAGRAM, BURST OFF
1ns/div
V
MOD+
V
BIAS+
BURST-DISABLE
SIGNAL
Typical Operating Characteristics (continued)
(T
A
= +25
°
C, unless otherwise noted.)
Pin Description
PIN
NAME
FUNCTION
1, 4, 9,
15, 18, 21
V
CC
Power-Supply Voltage
2
3
5
6
IN+
IN-
BEN+
BEN-
Noninverting Data Input with On-Chip Biasing
Inverting Data Input with On-Chip Biasing
Noninverting Burst-Enable Input with On-Chip Biasing
Inverting Burst-Enable Input with On-Chip Biasing
7
EN
TTL/CMOS Enable Input. Low for normal operation. Float or pull high to disable laser bias and
modulation currents.
8, 11, 19
10
12
13
GND
FAIL
LONGB
BIAS-
Power-Supply Ground
TTL/CMOS Failure Output. Indicates APC failure when low.
TTL/CMOS Long Burst (See the
Setting the LONGB Input Pin
Section)
Inverting Laser Bias-Current Output. Connect through 15
to V
CC
.
Noninverting Laser Bias-Current Output. Bias current flows into this pin when BEN is high. Minimize
capacitance on this pin.
14
BIAS+
16
OUT+
Noninverting Laser Modulation-Current Output. Modulation current flows into this pin when BEN and IN
are high.
17
OUT-
Inverting Laser Modulation-Current Output. Connect through 15
to V
CC
.
Monitor Diode Input. Connect this pin to the anode of the monitor diode. Leave floating for open-loop
operation. Minimize capacitance on this pin.
20
MD
22
BIASMAX
Maximum Bias Current Set. A resistor connected from this pin to ground sets the maximum bias
current. The bias current cannot exceed this level. The APC loop controls the bias current up to the
level of the BIASMAX. For APC open-loop operation, this pin sets the laser bias current.
23
MODSET
M od ul ati on C ur ent S et. A r esi stor connected fr om thi s p n to g ound sets the d esi ed m od ul ati on cur ent.
24
APCSET
Average Power Control Set. A resistor connected from this pin to ground sets the desired average
optical power. Connect a 50k
resistor to ground for APC open-loop operation.
Ground. This pad must be soldered to ground.
EP
Exposed Pad
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3656 | Dual LVDS Transmitter/Receiver 16-SOIC -40 to 85 |
| MAX3656E | Dual LVDS Transmitter/Receiver 16-SOIC -40 to 85 |
| MAX3664 | Single LVDS Transmitter 5-SOT-23 -40 to 85 |
| MAX3664ESA | Single LVDS Transmitter 5-SOT-23 -40 to 85 |
| MAX3665 | Single LVDS Transmitter 5-SOT-23 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3656ETG+ | 功能描述:激光驅動器 .155-2.5Gbps Burst Mode Laser Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3656ETG+ | 制造商:Maxim Integrated Products 功能描述:IC LASER DIODE DRIVER 2.5GBPS TQFN-24 |
| MAX3656ETG+D | 制造商:Maxim Integrated Products 功能描述:LASER DRVR 2.5GBPS 1CH 24TQFN EP - Rail/Tube |
| MAX3656ETG+T | 功能描述:激光驅動器 .155-2.5Gbps Burst Mode Laser Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3656ETG+TD | 制造商:Maxim Integrated Products 功能描述:LASER DRVR 2.5GBPS 1CH 24TQFN EP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。