- 您現在的位置：買賣IC網 > PDF目錄385526 > MAX3386ECUP (MAXIM INTEGRATED PRODUCTS INC) Dual LVDS Receiver 8-MSOP -40 to 85 PDF資料下載
參數資料
| 型號： | MAX3386ECUP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Dual LVDS Receiver 8-MSOP -40 to 85 |
| 中文描述： | DUAL LINE TRANSCEIVER, PDSO20 |
| 封裝： | 4.40 MM, 0.65 MM PITCH, TSSOP-20 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 156K |
| 代理商： | MAX3386ECUP |
M
3.0V, ±15kV ESD-Protected RS-232
Transceiver for PDAs and Cell Phones
_______________________________________________________________________________________
7
V
L
Logic Supply Input
Unlike other RS-232 interface devices where the receiver
outputs swing between 0 and V
CC
, the MAX3386E fea-
tures a separate logic supply input (V
L
) that sets V
OH
for the receiver outputs and sets thresholds for the
receiver inputs. This feature allows a great deal of flexi-
bility in interfacing to many different types of systems
with different logic levels. Connect this input to the host
logic supply (1.8V
≤
V
L
≤
V
CC
). Also see the Typical
PDA/Cell-Phone Application section.
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures are
incorporated on all pins to protect against electrostatic
discharges (ESDs) encountered during handling and
assembly. The MAX3386E’s driver outputs and receiver
inputs have extra protection against static electricity.
Maxim has developed state-of-the-art structures to pro-
tect these pins against an ESD of ±15kV without damage.
The ESD structures withstand high ESD in all states: nor-
mal operation, shutdown, and powered down. After an
ESD event, Maxim’s “E” version devices keep working
without latchup, whereas competing RS-232 products
can latch and must be powered down to remove latchup.
ESD protection can be tested in various ways. The trans-
mitter outputs and receiver inputs of this product family
are characterized for protection to the following limits:
1) ±15kV using the Human Body Model
2) ±8kV using the Contact Discharge method specified
in IEC 1000-4-2
3) ±15kV using IEC 1000-4-2’s Air-Gap Discharge
method
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, methodology, and results.
Human Body Model
Figure 3a shows the Human Body Model, and Figure 3b
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.5k
resistor.
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifi-
cally refer to ICs. The MAX3386E helps you design
equipment that meets Level 4 (the highest level) of IEC
1000-4-2, without the need for additional ESD-protection
components.
The major difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2, because series resistance is
lower in the IEC 1000-4-2 model. Hence, the ESD with-
stand voltage measured to IEC 1000-4-2 is generally
lower than that measured using the Human Body
Model. Figure 4a shows the IEC 1000-4-2 model, and
Figure 4b shows the current waveform for the ±8kV IEC
1000-4-2 Level 4 ESD Contact-Discharge test.
The air-gap test involves approaching the device with a
charged probe. The contact-discharge method connects
the probe to the device before the probe is energized.
CHARGE-CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
100pF
R
C
1M
R
D
1500
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 3a. Human Body ESD Test Model
I
P
100%
90%
36.8%
t
RL
TIME
t
DL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
Ir
10%
0
0
AMPERES
Figure 3b. Human Body Current Waveform
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3387E | +3.0V to +5.5V, 10nA, 250kbps RS-232 Transceivers with ±15kV ESD-Protected I/O and Logic Pins I1(+3.0V至+5.5V,10nA,帶 ±15kV ESD保護接口和邏輯引腳，250kbps RS-232 收發器（3收3發）) |
| MAX338 | 8-Channel,Low-Leakage, CMOS Analog Multiplexers(接通電阻400Ω,漏電流0.02nA,導通速率0.5μs,模擬多路轉換器) |
| MAX339 | Dual 4-Channel,Low-Leakage, CMOS Analog Multiplexers(接通電阻400Ω,漏電流0.02nA,導通速率0.5μs,模擬多路轉換器) |
| MAX3406 | 75з/100з/120з Switchable Termination Networks |
| MAX3406EUK | 75з/100з/120з Switchable Termination Networks |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3386ECUP+ | 功能描述:RS-232接口集成電路 3V Transceiver for PDAs & Cells RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3386ECUP+T | 功能描述:RS-232接口集成電路 3V Transceiver for PDAs & Cells RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3386ECUP-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3386EEUP | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3386EEUP+ | 功能描述:RS-232接口集成電路 3V Transceiver for PDAs & Cells RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。