- 您現在的位置：買賣IC網 > PDF目錄9772 > MAX3325EAI+ (Maxim Integrated Products)IC TXRX DUAL RS232 LCD 28-SSOP PDF資料下載
參數資料
| 型號： | MAX3325EAI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX DUAL RS232 LCD 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 46 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | RS232 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
Detailed Description
Dual Charge-Pump Voltage Converter
The MAX3325’s internal power supply consists of a reg-
ulated dual charge pump that provides output voltages
of +5.5V (doubling charge pump) and -5.5V (inverting
charge pump) over the 3.0V to 3.6V VDD range. The
charge pump operates in discontinuous mode; if the
output voltages are less than 5.5V, the charge pump is
enabled; if the output voltages exceed 5.5V, the charge
pump is disabled. Each charge pump requires a flying
capacitor (C1, C2) and a reservoir capacitor (C3, C4)
to generate the V+ and V- supplies (Figure 1).
RS-232 Transmitters
The transmitters are inverting level translators that con-
vert logic levels to ±5.0V EIA/TIA-232 levels. The
MAX3325 transmitters guarantee a 250kbps data rate
with worst-case loads of 3k
in parallel with 1000pF,
providing compatibility with PC-to-PC communication
software (such as LapLink).
The MAX3325’s transmitters are disabled and the out-
puts are forced into a high-impedance state when the
RS-232 circuitry is in shutdown (
SD232 = low). The
MAX3325 permits the outputs to be driven up to ±13V
in shutdown.
The transmitter inputs do not have pull-up resistors.
Connect unused inputs to GND or VDD.
RS-232 Receivers
The receivers convert RS-232 signals to logic output
levels. The VL pin controls the logic output high voltage.
The receiver outputs are always active, regardless of
the shutdown state.
Positive Voltage Regulator
The MAX3325 has a regulated +5V output suitable for
powering +5V LCD modules or other circuits. The out-
put of the boost charge pump is regulated with an LDO
linear regulator. The REG output sources up to 11mA of
current to external circuitry.
Adjustable LCD Supply
The LCD output provides a flexible output voltage to
adjust the contrast of LCD modules. The output voltage
range is determined by the external circuitry connected
to LCD, FB, DAC, REF+ (or REF-, depending on con-
trast polarity). Additionally, the TEMP output can be
used to automatically compensate the contrast adjust-
ment for temperature variance.
The LCD output is a linear regulator powered by the neg-
ative charge pump. It is capable of sinking up to 3mA of
current. Although the LCD regulator can be adjusted to
positive voltages, it is not capable of sourcing current. A
minimum output current of 100A is required.
6-Bit DAC
The MAX3325’s DAC output is an unbuffered inverted
R2R structure with an output voltage range of 0 to
+1.2V. The DAC output impedance is typically 50k
,
and can be connected through a series resistor to the
FB input of the LCD regulator. An internal power-on
reset circuit sets the DAC to midscale on power-up.
DAC Control Inputs
The DAC code is controlled by
UP and DOWN to adjust
the contrast of the LCD module. These inputs are
intended to interface to digital signals, but do not
include debounce circuitry. See the
Applications sec-
tion. See Table 1 for the truth table.
Temperature Compensation
The MAX3325’s TEMP output is used to minimize devia-
tion in LCD contrast level due to temperature changes.
The TEMP output is capable of sinking or sourcing up
to 22A to the external resistor network.
Shutdown Mode
Supply current falls below 1A in shutdown mode
(
SDLCD = SD232 = low). When shut down, the device’s
charge pumps are shut off, V+ is pulled down to VDD,
V- is pulled to ground, and the transmitter outputs are
disabled (high impedance). The LCD section is also
powered down. The REG, LCD, and both reference out-
puts become high impedance. The time required to exit
shutdown is typically 100s, as shown in the
Typical
Operating Characteristics. However, the TEMP output
requires 50ms to fully stabilize. Connect
SDLCD and
SD232 to VDD if the shutdown mode is not used. See
Table 2.
MAX3325
3V Dual RS-232 Transceiver with
LCD Supply and Contrast Controller
8
_______________________________________________________________________________________
LapLink is a trademark of Traveling Software.
X = Don’t care
Table 1. DAC Truth Table
Table 2. Shutdown Truth Table
UP
0
1
↓
DOWN
0
↓
1
FUNCTION
DAC set to midscale
DAC register decrements 1 count
DAC register increments 1 count
SDLCD
0
1
X
SD232
0
X
1
FUNCTION
Low-power shutdown mode
LCD bias and REG outputs enabled
RS-232 transmitters enabled
相關PDF資料 |
PDF描述 |
|---|---|
| VE-26N-IU-F3 | CONVERTER MOD DC/DC 18.5V 200W |
| VE-26N-IU-F2 | CONVERTER MOD DC/DC 18.5V 200W |
| MXL1535EEWI+T | IC TXRX RS485/422 28-SOIC |
| VE-26N-IU-F1 | CONVERTER MOD DC/DC 18.5V 200W |
| MAX251ESD+T | IC RS-232 DRVR RX 5V 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3325EAI+ | 功能描述:RS-232接口集成電路 3V Dual Tcvr w/LCD S&C Controller RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3325EAI+T | 功能描述:RS-232接口集成電路 3V Dual Tcvr w/LCD S&C Controller RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3325EAI-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3325ENI | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX332CPE | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。