• <ins id="nvinr"><label id="nvinr"></label></ins>
  • <pre id="nvinr"></pre>
    <tbody id="nvinr"><strike id="nvinr"></strike></tbody>
    <kbd id="nvinr"></kbd>
    <input id="nvinr"><span id="nvinr"></span></input>
    <ins id="nvinr"><label id="nvinr"></label></ins>
    <kbd id="nvinr"><th id="nvinr"></th></kbd>
    <label id="nvinr"></label>
    <em id="nvinr"><sup id="nvinr"></sup></em>
  • <tbody id="nvinr"><span id="nvinr"></span></tbody>
    參數資料
    型號: MAX3317CUP
    廠商: MAXIM INTEGRATED PRODUCTS INC
    元件分類: 通用總線功能
    英文描述: 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
    中文描述: LINE TRANSCEIVER, PDSO20
    封裝: TSSOP-20
    文件頁數: 7/16頁
    文件大小: 190K
    代理商: MAX3317CUP
    M
    ±15kV ESD-Protected, 2.5V, 1μA, 460kbps,
    RS-232 Compatible Transceivers
    _______________________________________________________________________________________
    7
    Pin Description (continued)
    Detailed Description
    Dual Charge-Pump Voltage Converter
    The MAX3316E–MAX3319Es’ internal power supply
    consists of a regulated dual charge pump that provides
    output voltages of +4.4V (doubling charge pump) and
    -4.3V (inverting charge pump), over the +2.25V to
    +3.0V range. The charge pump operates in discontinu-
    ous mode: if the output voltages are less than 4.4V, the
    charge pump is enabled; if the output voltages exceed
    4.4V, the charge pump is disabled. Each charge pump
    requires a flying capacitor (C1, C2) and a reservoir
    capacitor (C3, C4) to generate the V+ and V- supplies.
    The READY output (MAX3318E/MAX3319E) is low
    when the charge pumps are disabled in shutdown
    mode. The READY signal asserts high when V- goes
    below -2.75V.
    RS-232 Compatible Transmitters
    The MAX3316E–MAX3319Es’ transmitters are inverting
    level translators that convert CMOS-logic levels to
    RS-232 compatible voltage levels. They guarantee a
    460kbps data rate with worst-case loads of 3k
    in parallel
    with 1000pF, providing compatibility with PC-to-PC
    communication software (such as LapLink).
    The MAX3317E’s transmitters are turned off (high
    impedance) when
    SHDN
    is asserted low, putting the
    device in shutdown mode. The MAX3318E/MAX3319Es’
    transmitters are turned off (high impedance) when
    FORCEOFF
    is asserted low, or when the AutoShutdown
    Plus circuitry senses that all receiver and transmitter
    inputs are inactive for more than 30 seconds.
    The transmitter outputs can be driven to ±12V when
    power is off. The transmitter inputs do not have internal
    pull-up resistors. Connect unused inputs to GND or V
    CC
    .
    RS-232 Receivers
    The MAX3316E–MAX3319Es’ receivers convert ±3.7V
    to ±13.2V RS-232 signal levels into CMOS-logic output
    levels. The receivers are rated to receive signals up to
    ±25V. The MAX3316E/MAX3318E/MAX3319Es’
    receivers feature inverting outputs that always remain
    active (Table 1). The MAX3317E’s receivers have
    inverting, three-state outputs. In shutdown, the
    receivers can be active or inactive (Table 2).
    The MAX3318E/MAX3319E feature an
    INVALID
    output
    that is asserted low when no valid RS-232 voltage levels
    have been detected on all receiver inputs. Because
    INVALID
    indicates the receiver’s input condition, it
    is independent of the states of FORCEON and
    FORCEOFF
    .
    MAX3317E Shutdown Mode
    Supply current falls to less than 1μA in shutdown mode
    (
    SHDN
    = low). When shut down, the device’s charge
    pumps are turned off, V+ is pulled down to V
    CC
    , V- is
    pulled to ground, and the transmitter outputs are dis-
    abled (high impedance). The time required to exit shut-
    LapLink is a trademark of Traveling Software.
    PIN
    MAX3316E
    SSOP
    MAX3317E MAX3318E MAX3319E
    NAME
    FUNCTION
    Shutdown Control, Active Low
    Ready to Transmit Output, Active High. READY is
    enabled high when V- goes below -3.5V and the
    device is ready to transmit.
    Valid Signal Detector Output, Active Low. A logic
    high indicates that a valid RS-232 level is present
    on a receiver input.
    Force-On Input, Active High. Drive high to override
    AutoShutdown Plus, keeping transmitters and
    receivers on (
    FORCEOFF
    must be high) (Table 1).
    Force-Off Input, Active Low. Drive low to shut
    down transmitters, receivers, and charge pump.
    This overrides AutoShutdown Plus and FORCEON
    (Table 1).
    FORCEOFF
    FORCEON
    INVALID
    READY
    SHDN
    1
    10
    12
    16
    20
    14
    11
    1
    20
    TSSOP
    相關PDF資料
    PDF描述
    MAX3317EAP 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
    MAX3317EUP 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
    MAX3318 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
    MAX3318CAP 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
    MAX3318CUP 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
    相關代理商/技術參數
    參數描述
    MAX3317CUP+ 功能描述:RS-232接口集成電路 460kbps 1uA 2.5V Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
    MAX3317CUP+T 功能描述:RS-232接口集成電路 460kbps 1uA 2.5V Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
    MAX3317CUP-T 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
    MAX3317EAP 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
    MAX3317EAP+T 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: