- 您現在的位置：買賣IC網 > PDF目錄9815 > MAX3302EETI+T (Maxim Integrated Products)IC USB TXRX OTG 28-TQFN-EP PDF資料下載
參數資料
| 型號： | MAX3302EETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 19/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB TXRX OTG 28-TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 規程： | USB 2.0 |
| 電源電壓： | 3 V ~ 4.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
addressed at I2C register location 10h, 11h (as well as
locations 16h, 17h) to support USB OTG SIE implemen-
tations that are limited to I2C register addresses
between 0h and 15h.
ID and Manufacturer Register Address Map
Table 17 provides the contents of the ID registers of the
MAX3301E/MAX3302E. Addresses 00h and 01h com-
prise the vendor ID registers. Addresses 02h and 03h
comprise the product ID registers. Addresses 14h and
15h comprise the revision ID registers.
Audio Car Kit
Many cell phones are required to interface to car kits.
Depending upon the car kit, the interface to the phone
may be required to support any or all of the following
functions:
Audio input
Audio output
Charging
Control and status
D+ and D- of the MAX3301E/MAX3302E go to a high-
impedance state when in shutdown mode, allowing
external signals (including audio) to be multiplexed onto
these lines.
External Components
External Resistors
Two external resistors (27.4Ω ±1%) are required for
USB connection. Install one resistor in series between
D+ of the MAX3301E/MAX3302E and D+ of the USB
connector. Install the other resistor in series between D-
of the MAX3301E/MAX3302E and D- of the USB con-
nector (see the
Typical Operating Circuit).
External Capacitors
Five external capacitors are recommended for proper
operation. Install all capacitors as close to the device as
possible. Decouple VL to GND with a 0.1F ceramic
capacitor. Bypass VCC to GND with a 1F ceramic
capacitor. Bypass TRM to GND with a 1F (or greater)
ceramic or plastic capacitor. Connect a 100nF flying
capacitor between C+ and C- for the charge pump (see
the
Typical Operating Circuit). Bypass VBUS to GND
with a 1F to 6.5F ceramic capacitor in accordance
with USB OTG specifications.
ESD Protection
To protect the MAX3301E/MAX3302E against ESD, D+,
D-, ID_IN, and VBUS, have extra protection against stat-
ic electricity to protect the device up to ±15kV. The ESD
structures withstand high ESD in all states; normal oper-
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
26
______________________________________________________________________________________
BIT NUMBER
SYMBOL
CONTENTS
VALUE AT
POWER-UP
0
vbus_vld
Set to 0 to disable the vbus_vld interrupt for a low-to-high transition. Set to 1 to
enable the vbus_vld interrupt for a low-to-high transition. See Tables 10 and 11.
0
1
sess_vld
Set to 0 to disable the sess_vld interrupt for a low-to-high transition. Set to 1 to
enable the sess_vld interrupt for a low-to-high transition. See Tables 10 and 11.
0
2
dp_hi
Set to 0 to disable the dp_hi interrupt for a low-to-high transition. Set to 1 to
enable the dp_hi interrupt for a low-to-high transition. See Tables 10 and 11.
0
3
id_gnd
Set to 0 to disable the id_gnd interrupt for a low-to-high transition. Set to 1 to
enable the id_gnd interrupt for a low-to-high transition. See Tables 10 and 11.
0
4
dm_hi
Set to 0 to disable the dm_hi interrupt for a low-to-high transition. Set to 1 to
enable the dm_hi interrupt for a low-to-high transition. See Tables 10 and 11.
0
5
id_float
Set to 0 to disable the id_float interrupt for a low-to-high transition. Set to 1 to
enable the id_float interrupt for a low-to-high transition. See Tables 10 and 11.
0
6
bdis_acon
Set to 0 to disable the bdis_acon interrupt for a low-to-high transition. Set to 1 to
enable the bdis_acon interrupt for a low-to-high transition. See Tables 10 and 11.
0
7
cr_int_sess_end
Set to 0 to disable the cr_int_sess_end interrupt for a low-to-high transition.
Set to 1 to enable the cr_int_sess_end interrupt for a low-to-high transition.
See Tables 10 and 11.
0
Table 13. Interrupt-Enable High Register (Write to Address 0Eh to Set, Write to Address
0Fh to Clear)
相關PDF資料 |
PDF描述 |
|---|---|
| MS27472T14F35PB | CONN RCPT 37POS WALL MNT W/PINS |
| MS27472T14B35PC | CONN RCPT 37POS WALL MNT W/PINS |
| MAX3318CUP+T | IC TXRX RS232 460KBPS 20-TSSOP |
| MS27467T21B16S | CONN PLUG 16POS STRAIGHT W/SCKT |
| MS3452W20-15P | CONN RCPT 7POS BOX MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3302EETJ+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube |
| MAX3302EEWA+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube |
| MAX3302EEWA+T | 功能描述:USB 接口集成電路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| MAX3311CUB | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3311CUB+ | 功能描述:RS-232接口集成電路 460kbps 1uA Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。