- 您現在的位置：買賣IC網 > PDF目錄384662 > MAX3296EVKIT-SW (Maxim Integrated Products, Inc.) MAX3296 Shortwave or VCSEL (Common Cathode) Evaluation Kit PDF資料下載
參數資料
| 型號： | MAX3296EVKIT-SW |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | MAX3296 Shortwave or VCSEL (Common Cathode) Evaluation Kit |
| 中文描述： | MAX3296短波或的VCSEL（共陰極）評估板 |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 1446K |
| 代理商： | MAX3296EVKIT-SW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
M
3.0V to 5.5V, 1.25Gbps/2.5Gbps
LAN Laser Drivers
______________________________________________________________________________________
11
force a shutdown if a fault is detected. The shutdown
condition is latched until reset by a toggle of EN,
EN
, or
power.
Another safety system, open fiber control (OFC), uses
safety interlocks to prevent eye hazards. To accommo-
date the OFC standard, the MAX3286/MAX3296 series
provide dual enable inputs and dual fault outputs.
The safety circuitry contains fault detection, dual enable
inputs, latched fault outputs, and a pulse generator
(Figure 6).
Safety circuitry monitors the APC circuit to detect unsafe
levels of laser emission during single-point failures. A
single-point failure can be a short to V
CC
or GND or a
short between any two IC pins.
Pulse Generator
During startup, the laser does not emit light and the
APC loop is not closed, triggering a fault signal. To
allow startup, an internal fault-delay pulse disables the
safety system for a programmable period of time, allowing
the driver to begin operation. The length of the pulse is
determined by the capacitor connected at FLTDLY and
should be set 5 to 10 times longer than the APC time
constant. The internal safety features can be disabled
by connecting FLTDLY to GND. Note that EN must be
high,
EN
must be low, and V
CC
must be in the opera-
tional range for laser operation.
Fault Detection
The MAX3286/MAX3296 series has extensive and com-
prehensive fault-detection features. All critical nodes
are monitored for safety faults, and any node voltage
that differs significantly from its expected value results
in a fault (Table 1). When a fault condition is detected,
the laser is shut down. See the
Applications Information
section for more information on laser safety.
Shutdown
The laser drivers offer dual redundant bias shutdown
mechanisms. The SHDNDRV output drives an optional
external MOSFET semiconductor. The bias and modu-
lation drivers have separate internal disable signals.
Latched Fault Output
Two complementary FAULT outputs are provided with
the MAX3286/MAX3296 series. In the event of a fault,
these outputs latch until one of three events occurs:
1) The power is switched off, then on.
V
CC
FLTDLY
FAULT
FAULT
SHDNDRV
(FROM POR CIRCUIT)
REF_FAULT
MONITOR_FAULT
MD_FAULT
POLARITY_FAULT
TC_FAULT
MOD_FAULT
EN
EN
ENABLE
Q
R
RESET
DOMINANT
FAULT
LATCH
S
FAULT
DETECTION
t
FLTDLY
PULSE GENERATOR
MAX3286
MAX3296
Figure 6. Simplified Safety Circuit Schematic
0.6
0.8
0.7
1.0
0.9
1.2
1.1
1.3
0
20 30 40
JUNCTION TEMPERATURE (
°
C)
10
50 60 70 80 90 100 110
I
M
/
M
°
C
R
TC
= OPEN
TEMPCO = 50ppm/
°
C
R
TC
≥
1.9k
R
= OPEN
TEMPCO = 4000ppm/
°
C
Figure 5. Modulation Current vs. Temperature for Maximum
and Minimum Temperature Coefficient
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3297CUE | 3.0V to 5.5V, 1.25Gbps/2.5Gbps LAN Laser Drivers |
| MAX3286-MAX3299 | 3.0V to 5.5V, 1.25Gbps/2.5Gbps LAN Laser Drivers |
| MAX3288CUE | 32-Bit Digital Signal Controller with Flash 128-LQFP -40 to 85 |
| MAX3298CUE | 3.0V to 5.5V, 1.25Gbps/2.5Gbps LAN Laser Drivers |
| MAX3289CUE | 3.0V to 5.5V, 1.25Gbps/2.5Gbps LAN Laser Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3297CUE | 功能描述:激光驅動器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3297CUE+ | 功能描述:激光驅動器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3297CUE+T | 功能描述:激光驅動器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3297CUE-T | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3298CUE | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。