- 您現在的位置：買賣IC網 > PDF目錄384662 > MAX3273 (Maxim Integrated Products, Inc.) 32-Bit Digital Signal Controller with Flash 100-LQFP -40 to 125 PDF資料下載
參數資料
| 型號： | MAX3273 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 32-Bit Digital Signal Controller with Flash 100-LQFP -40 to 125 |
| 中文描述： | +3.3V、2.5Gbps低功耗激光驅動器 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 984K |
| 代理商： | MAX3273 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
M
+3.3V, 2.5Gbps Low-Power Laser Driver
_______________________________________________________________________________________
7
Pin Description
PIN
NAME
V
CC
DATA+
DATA-
CLK+
CLK-
GND
LATCH
FUNCTION
1, 4, 13, 15, 18
2
3
5
6
7, 9, 12
8
Power-Supply Voltage
Noninverting Data Input, with On-Chip Biasing
Inverting Data Input, with On-Chip Biasing
Noninverting Clock Input for Data Retiming, with On-Chip Biasing
Inverting Clock Input for Data Retiming, with On-Chip Biasing
Ground
Data Retiming Enable Input, Active-High. Retiming disabled when floating or pulled low.
10
EN
TTL/CMOS Enable Input. Low for normal operation. Float or pull high to disable laser bias and
modulation currents. Internal 100k
pullup to V
CC
.
A resistor connected from this pin to ground sets the desired modulation current.
Laser Bias Current Output. Connect to the laser through an inductor.
Positive Modulation-Current Output. I
MOD
flows into this pin when input data is high.
Negative Modulation-Current Output. Current flows into this pin when input data is low. Connect
to load equivalent to that on OUT+ to maintain differential output balance.
11
14
16
MODSET
BIAS
OUT+
17
OUT-
19
MD
Monitor Diode Input. Connect this pin to the anode of the monitor diode. Leave floating for
open-loop operation.
20
APCFILT1
A capacitor between APCFILT1 and APCFILT2 sets the dominant pole of the APC feedback
loop (C
APCFILT
= 0.01μF). Ground APCFILT1 for open-loop operation.
See above.
TTL/CMOS Failure Output, Active-Low. Indicates APC failure when low.
21
22
APCFILT2
FAIL
23
APCSET
A resistor connected from this pin to ground sets the desired average optical power. Connect a
100k
resistor to GND for open-loop operation.
24
BIASMAX
A resistor connected from this pin to ground sets the maximum bias current. The APC function
can subtract current from this maximum value, but cannot add to it. For open-loop operation,
this pin sets the laser bias current.
EP
EXPOSED
PAD
Ground. Solder this pad to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3273EGG | +3.3V, 2.5Gbps Low-Power Laser Driver |
| MAX3274UGE | Dual-Rate Fibre Channel Limiting Amplifier |
| MAX3274 | 32-Bit Digital Signal Controller with Flash 100-BGA MICROSTAR -40 to 85 |
| MAX327CPE | Quad, SPST, Ultra-Low Leakage, CMOS Analog Switches |
| MAX327CSE | Quad, SPST, Ultra-Low Leakage, CMOS Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3273E/D | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3273EGG | 功能描述:激光驅動器 2.5Gbps Low-Power Laser Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3273EGG-T | 功能描述:激光驅動器 2.5Gbps Low-Power Laser Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3273ETG+ | 功能描述:激光驅動器 2.5Gbps Low-Power Laser Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3273ETG+T | 功能描述:激光驅動器 2.5Gbps Low-Power Laser Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。