- 您現在的位置：買賣IC網 > PDF目錄9841 > MAX3227EEUE+T (Maxim Integrated Products)IC TXRX RS232 1MBPS SD 16TSSOP PDF資料下載
參數資料
| 型號： | MAX3227EEUE+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS232 1MBPS SD 16TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS232 |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
±15kV ESD-Protected, 1A, 1Mbps 3.0V to 5.5V,
RS-232 Transceivers with AutoShutdown Plus
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and per-
formance of finished equipment; it does not specifically
refer to integrated circuits. The MAX3224E–MAX3227E,
MAX3244E/MAX3245E help you design equipment that
meets Level 4 (the highest level) of IEC 1000-4-2, with-
out the need for additional ESD-protection components.
The major difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2, because series resistance is
lower in the IEC 1000-4-2 model. Hence, the ESD with-
stand voltage measured to IEC 1000-4-2 is generally
lower than that measured using the Human Body
Model. Figure 7a shows the IEC 1000-4-2 model and
Figure 7b shows the current waveform for the 8kV, IEC
1000-4-2, Level 4, ESD Contact-Discharge Method.
The Air-Gap Method involves approaching the device
with a charged probe. The Contact-Discharge Method
connects the probe to the device before the probe is
energized.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resis-
tance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. Of course, all pins require this protec-
tion during manufacturing, not just RS-232 inputs and
outputs. Therefore, after PC board assembly, the
Machine Model is less relevant to I/O ports.
__________Applications Information
Capacitor Selection
The capacitor type used for C1–C4 is not critical for
proper operation; polarized or nonpolarized capacitors
can be used. The charge pump requires 0.1F capaci-
tors for 3.3V operation. For other supply voltages, see
Table 3 for required capacitor values. Do not use val-
ues smaller than those listed in Table 3. Increasing the
capacitor values (e.g., by a factor of 2) reduces ripple
on the transmitter outputs and slightly reduces power
consumption. C2, C3, and C4 can be increased without
changing C1’s value. However, do not increase C1
without also increasing the values of C2, C3, C4,
and CBYPASS, to maintain the proper ratios (C1 to
the other capacitors).
When using the minimum required capacitor values,
make sure the capacitor value does not degrade
excessively with temperature. If in doubt, use capaci-
tors with a larger nominal value. The capacitor’s equiv-
alent series resistance (ESR), which usually rises at low
temperatures, influences the amount of ripple on V+
and V-.
Power-Supply Decoupling
In most circumstances, a 0.1F VCC bypass capacitor
is adequate. In applications that are sensitive to power-
supply noise, use a capacitor of the same value as
charge-pump capacitor C1. Connect bypass capaci-
tors as close to the IC as possible.
Transmitter Outputs
when Exiting Shutdown
Figure 8 shows two transmitter outputs when exiting
shutdown mode. As they become active, the two trans-
mitter outputs are shown going to opposite RS-232 lev-
els (one transmitter input is high, the other is low). Each
VCC
(V)
C2, C3, C4
(
F)
3.0 to 3.6
0.22
3.15 to 3.6
0.1
C1, CBYPASS
(
F)
0.22
0.1
4.5 to 5.5
0.33
3.0 to 5.5
1
0.047
0.22
Table 3. Required Minimum Capacitance
Values
5
μs/div
T1OUT
FORCEON = FORCEOFF
T2OUT
READY
5V/div
0
2V/div
0
5V/div
0
VCC = 3.3V
C1–C4 = 0.1
μF
Figure 8. Transmitter Outputs when Exiting Shutdown or
Powering Up
14
Maxim Integrated
MAX3224E/MAX3225E/
MAX3226E/MAX3227E/MAX3244E/MAX3245E
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484E22F55PA | CONN PLUG 55POS STRAIGHT W/PINS |
| V28C28M100BG | CONVERTER MOD DC/DC 28V 100W |
| VI-J40-MX-F2 | CONVERTER MOD DC/DC 5V 75W |
| VI-J40-MX-F1 | CONVERTER MOD DC/DC 5V 75W |
| MS3111P16-8S | CONN RCPT 8POS CBL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3227EIDB | 功能描述:RS-232接口集成電路 3-5.5V Single-Ch Line Drvr/Rcvr RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3227EIDBG4 | 功能描述:RS-232接口集成電路 3-5.5V Sgl-Ch RS-232 Line Drvr/Rcvr RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3227EIDBR | 功能描述:RS-232接口集成電路 3-5.5V Single-Ch Line Drvr/Rcvr RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3227EIDBRG4 | 功能描述:RS-232接口集成電路 3-5.5V Sgl-Ch RS-232 Line Drvr/Rcvr RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3227EUE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。