![](http://datasheet.mmic.net.cn/390000/MAX3140EEI_datasheet_16817838/MAX3140EEI_1.png)
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
General Desc ription
The MAX3140 is a complete universal asynchronous
receiver-transmitter (UART) and a true fail-safe RS-
485/RS-422 transceiver combined in a single 28-pin
QSOP package for space-, cost-, and power-con-
strained applications. The MAX3140 saves additional
board space as well as microcontroller (μC) I/O pins by
featuring an SPI /QSPI /MICROWIRE -compatible
serial interface. It is pin-programmable for configuration
in all RS-485/RS-422 networks.
The MAX3140 includes a single RS-485/RS-422 driver
and receiver featuring true fail-safe circuitry, which
guarantees a logic-high receiver output when the
receiver inputs are open or shorted. This feature pro-
vides immunity to faults without requiring complex ter-
mination. The MAX3140 provides software-selectable
control of half- or full-duplex operation, data rate, slew
rate, and transmitter and receiver phase. The RS-485
driver slew rate is programmable to minimize EMI and
results in maximum data rates of 115kbps, 500kbps,
and 10Mbps. Independent transmitter/receiver phase
control enables software correction of twisted-pair
polarity reversal. A 1/8-unit-load receiver input imped-
ance allows up to 256 transceivers on the bus.
The MAX3140’s UART includes an oscillator circuit
derived from an external crystal, and a baud-rate gen-
erator with software-programmable divider ratios for all
common baud rates from 300 baud to 230k baud. The
UART features an 8-word-deep receive FIFO that mini-
mizes processor overhead and provides a flexible inter-
rupt with four maskable sources, including address
recognition on 9-bit networks. Two control lines are
included for hardware handshaking—one input and
one output.
The MAX3140 operates from a single +5V supply and
typically consumes only 645μA with the receiver active.
Hardware-invoked shutdown reduces supply current to
only 20μA. The UART and RS-485/RS-422 functions can
be used together or independently since the two func-
tions share only supply and ground connections (the
MAX3140 is hardware- and software-compatible with the
MAX3100 and MAX3089).
Applic ations
Transceivers for EMI-
Sensitive Applications
Embedded Systems
Intelligent Instrumentation
Industrial-Control
Local Area Networks
HVAC and Building Control
Point-of-Sale Devices
Features
o
Integrated UART and RS-485/RS-422 Transceiver
in a Single 28-Pin QSOP
o
SPI/MICROWIRE-Compatible Interface Saves μC
I/O Pins
o
True Fail-Safe Receiver Output Eliminates
Complex Network Termination
o
Pin-Programmable RS-485/RS-422 Features
Half/Full-Duplex Operation
Slew-Rate Limiting for Reduced EMI
115kbps/500kbps/10Mbps Data Rates
Receiver/Transmitter Phase for Twisted-Pair
Polarity Reversal
o
Full-Featured UART
Programmable Up to 230k baud with a
3.6864MHz Crystal
8-Word Receive FIFO Minimizes Processor
Overhead
9-Bit Address-Recognition Interrupt
o
Allows Up to 256 Transceivers on the Bus
o
Low 20μA Hardware Shutdown Mode
o
Hardware/Software-Compatible with MAX3100
and MAX3089
M
SPI/MICROWIRE-Compatible UART with Integrated
True Fail-Safe RS-485/RS-422 Transceivers
________________________________________________________________ Maxim Integrated Products
1
19-1453; Rev 0; 6/99
PART
MAX3140CEI
MAX3140EEI
-40°C to +85°C
0°C to +70°C
TEMP. RANGE
PIN-PACKAGE
28 QSOP
28 QSOP
Ordering Information
SPI/QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
Pin Configuration appears at end of data sheet.
Typic al Applic ation Circ uit
CS
SCLK
DIN
DOUT
SPI/
MICRO-
WIRE
μ
P
UART
IRQ
H/FSRL
R
t
HALF/FULL-DUPLEX
RS-485/RS-422
R
t
TXP
CONTROL
LOGIC
RS-485
RS-422
RXP
MAX3140