SPI/I2C UART with 128-Word FIFOs Bit 7: EchoSuprs Set the EchoSuprs bit high so " />
參數資料
型號： MAX3107EAG+
廠商： Maxim Integrated Products
文件頁數： 26/52頁
文件大小： 0K
描述： IC UART SPI/I2C 128 FIFO 24SSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 58
特點： 內部振蕩器
通道數： 4，QUART
FIFO's： 128 字節
規程： RS232，RS485
電源電壓： 2.35 V ~ 3.6 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 24-SSOP
包裝： 管件
SPI/I2C UART with 128-Word FIFOs
Bit 7: EchoSuprs
Set the EchoSuprs bit high so that the MAX3107’s receiver gates any data it receives when its transmitter is busy
transmitting. In half-duplex communication (like IrDA and RS-485) this allows blocking of the locally echoed data. The
receiver can block data for an extended time after the transmitter ceases transmission by programming a hold time in
HDplxDelay[3:0] bits.
Bit 6: MultiDrop
Set the MultiDrop bit high to enable the 9-bit multidrop mode. If this bit is set, parity checking is not performed by the
receiver and parity generation is not done by the transmitter. The parity error bit, LSR[2], has a different meaning in
this case. The parity error bit represents the 9th bit (address/data indication) that is received with each 9-bit character.
Bit 5: Loopback
Set the Loopback bit high to enable internal local loopback mode. This internally connects TX to RX and also RTS/
CLKOUT to CTS. In local loopback mode, the TX output and the RX output are disconnected from the internal transmit-
ter and receiver. The TX output is in three-state. The RTS output remains connected to the internal logic and reflects the
logic state programmed in LCR[7]. The CTS input is disconnected from RTS and the internal logic. CTS thus remains
in a high-impedance state.
Bit 4: SpecialChr
The SpecialChr bit enables special character detection. The receiver can detect up to four special characters, as
selected in FlowCtrl:[5:4] and defined in the XON1, XON2, XOFF1 and/or XOFF2 registers, possibly in combination with
GPIO_ inputs, enabled through FlowCtrl[2]: GPIAddr. When a special character is received it is put into the RxFIFO and
a special character detect interrupt ISR[1] is generated.
Special character detection can be used in addition to auto XON/XOFF flow control, if enabled through FlowCtrl[3]. In
this case XON/OFF flow control is then limited to single character XON and XOFF and only two special characters can
then be defined (in XON2 and XOFF2).
Bit 3: RxEmtyInv
The RxEmtyInv bit inverts the meaning of the receiver empty interrupt: ISR[6]: RxEmtyInt. If RxEmtyInv is set low (default
state), the ISR[6] interrupt is generated when the receive FIFO is empty. If the RxEmtyInv is set high, the ISR[6] interrupt
is generated when data is put into the empty receive FIFO.
Bit 2: RxTrigInv
The RxTrigInv bit inverts the meaning of the RxFIFO triggering. When set, an ISR[3]: RFifoTrigInt is generated when
the RxFIFO is emptied to the trigger level: FIFOTrgLvl[7:4]. If the RxTrgInv bit is low (default state), the ISR[3] interrupt
is generated when the RxFIFO fill level that starts from a level below FIFOTrgLvl[7:4] is filled up to the trigger level
programmed into FIFOTrgLvl[7:4].
Bit 1: FIFORst
Set the FIFORst bit high to clear both the receive and transmit FIFOs of all data contents. After the FIFO reset, the
FIFORst bit must then be set back to 0 to continue normal operation.
Bit 0: RST
Set the RST bit high to reset the MAX3107. The SPI/I2C bus stays active during this reset, therefore, communication
with the MAX3107 is possible. All register bits are reset to their reset state and all FIFOs are cleared.
Once set high, the RST bit must be cleared by writing a 0 to RST.
MODE2 Register
ADDRESS:
0x0A
MODE:
R/W
BIT
7
6
5
4
3
2
1
0
NAME
EchoSuprs
MultiDrop
Loopback
SpecialChr
RxEmtyInv
RxTrigInv
FIFORst
RST
RESET
0
32
Maxim Integrated
MAX3107
相關PDF資料
PDF描述
MAX3108EWA+T IC UART
MAX3109ETJ+ SEMICONDUCTOR OTHER
MAX310CPE IC VIDEO MULTIPLEXER 8X1 16DIP
MAX3110EENI+G36 IC UART SPI COMPAT 28-DIP
MAX3120CUA+ IC TXRX INFRARED IRDA 8-UMAX
相關代理商/技術參數
參數描述
MAX3107EAG+ 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3107EAG+T 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3107ETG/V+ 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3107ETG/V+T 功能描述:UART 接口集成電路 SPI/IC UART with 128-Word FIFOs and Internal Oscillator RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3107ETG+ 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*