- 您現在的位置：買賣IC網 > PDF目錄384659 > MAX3100EPD (MAXIM INTEGRATED PRODUCTS INC) Dual LVDS Transmitter 8-MSOP-PowerPAD -40 to 85 PDF資料下載
參數資料
| 型號： | MAX3100EPD |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Dual LVDS Transmitter 8-MSOP-PowerPAD -40 to 85 |
| 中文描述： | 1 CHANNEL(S), 230.4K bps, SERIAL COMM CONTROLLER, PDIP14 |
| 封裝： | PLASTIC, DIP-14 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 263K |
| 代理商： | MAX3100EPD |
M
S PI/Mic rowire-Compatible
UART in QS OP-16
_______________________________________________________________________________________
5
______________________________________________________________Pin Desc ription
Crystal Connection. X1 also serves as an external clock input. See Crystal-Oscillator
Operation—X1, X2 Connection section.
9
10
General-Purpose Active-Low Input. Read via the
CTS
register bit; often used for RS-232 clear-
to-send input (Table 1).
General-Purpose Active-Low Output. Controlled by the
RTS
register bit. Often used for
RS-232 request-to-send output or RS-485 driver enable.
10
11
11
13
Asynchronous Serial-Data (receiver) Input. The serial information received from the modem or
RS-232/RS-485 receiver. A transition on RX while in shutdown generates an interrupt (Table 5).
12
14
Asynchronous Serial-Data (transmitter) Output
13
15
Active-Low Interrupt Output. Open-drain interrupt output to microprocessor.
5
6
Hardware-Shutdown Input. When shut down (
SHDN
= 0), the oscillator turns off immediately
without waiting for the current transmission to end, reducing supply current to just leakage
currents.
6
7
Ground
7
8
Crystal Connection. Leave X2 unconnected for external clock. See Crystal-Oscillator
Operation—X1, X2 Connection section.
8
9
Active-Low Chip-Select Input. DOUT goes high impedance when
CS
is high.
IRQ
, TX, and
RTS
are always active. Schmitt-trigger input.
4
4
SPI/Microwire Serial-Clock Input. Schmitt-trigger input.
3
3
SPI/Microwire Serial-Data Output. High impedance when
CS
is high.
2
2
SPI/Microwire Serial-Data Input. Schmitt-trigger input.
1
1
X1
CTS
RTS
RX
TX
IRQ
SHDN
GND
X2
CS
SCLK
DOUT
DIN
Positive Supply Pin (2.7V to 5.5V)
14
16
No Connection. Not internally connected.
—
5, 12
V
CC
N.C.
PIN
QSOP
FUNCTION
DIP
NAME
_______________Detailed Desc ription
The MAX3100 universal asynchronous receiver trans-
mitter (UART) interfaces the SPI/Microwire-compatible,
synchronous serial data from a microprocessor (μP) to
asynchronous, serial-data communication ports (RS-
232, RS-485, IrDA). Figure 2 shows the MAX3100 func-
tional diagram.
The MAX3100 combines a simple UART and a baud-rate
generator with an SPI interface and an interrupt genera-
tor. Configure the UART by writing a 16-bit word to a
write-configuration register, which contains the baud rate,
data-word length, parity enable, and enable of the 8-word
receive first-in/first-out (FIFO). The write configuration
selects between normal UART timing and IrDA timing,
controls shutdown, and contains 4 interrupt mask bits.
Transmit data by writing a 16-bit word to a write-data
register, where the last 7 or 8 bits are actual data to be
transmitted. Also included is the state of the transmitted
parity bit (if enabled). This register controls the state of
the
RTS
output pin. Received words generate an inter-
rupt if the receive-bit interrupt is enabled.
Read data from a 16-bit register that holds the oldest
data from the receive FIFO, the received parity data,
and the logic level at the
CTS
input pin. This register
also contains a bit that is the framing error in normal
operation and a receive-activity indicator in shutdown.
The baud-rate generator determines the rate at which the
transmitter and receiver operate. Bits B0 to B3 in the
write-configuration register determine the baud-rate divi-
sor (BRD), which divides down the X1 oscillator frequen-
cy. The baud clock is 16 times the data rate (baud rate).
The transmitter section accepts SPI/Microwire data, for-
mats it, and transmits it in asynchronous serial format
from the TX output. Data is loaded into the transmit-
buffer register from the SPI/Microwire interface. The
MAX3100 adds start and stop bits to the data and
clocks the data out at the selected baud rate (Table 7).
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3100 | Dual LVDS Transmitter 8-MSOP-PowerPAD -40 to 85 |
| MAX3100CEE | Dual LVDS Transmitter 8-MSOP-PowerPAD -40 to 85 |
| MAX3100CPD | Dual LVDS Transmitter 8-SOIC -40 to 85 |
| MAX3100EEE | Dual LVDS Transmitter 8-SOIC -40 to 85 |
| MAX3174CAI | #.3V Multiprotocol Software-Selectable Cable Terminators and Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3100EPD+ | 功能描述:UART 接口集成電路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3100ETG+ | 功能描述:UART 接口集成電路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3100ETG+T | 功能描述:UART 接口集成電路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3100EVKIT+ | 功能描述:界面開發工具 MAX3100 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX3107EAG+ | 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。